Agilent Technologies U1401B Скачать руководство пользователя страница 31 | Manualshive

Страница: 31 / 181

Agilent Technologies U1401B Скачать руководство пользователя страница 31

Getting Started

1

U1401B User’s and Service Guide

11

[1]

When the HOLD key is pressed for more then one second, its function depends on the present state of the instrument. If the
instrument is presently in the data hold mode, pressing this key for more than one second will exit the data hold mode; if the
instrument is not in the data hold mode, pressing this key for more than one second will enter or exit the dynamic recording
mode.

[2]

Only applicable when the instrument is in the dynamic recording mode.

[3]

Shifted functions.

7

SHIFT

Enables and disables the shifted functions of
the other keys

Toggles backlight ON/OFF

8

[3]

MODE

Selects output modes for constant
voltage/constant current, autoscan and
autoramp.
Selects frequency (Hz), duty cycle (%), pulse
width (ms), and level adjustments for square
wave output.

Enters the adjustment mode (for autoscan and
autoramp outputs).

9

[3]

Selects a digit or the polarity to be adjusted.

The selected digit/polarity will be flashing on
the secondary display.

—

10

[3]

Adjusts a digit or the polarity.
Press to adjust the selected digit or toggle the
output polarity.

—

11

[3]

OUTPUT

Toggles the output state on and off.

indicates that the signal is being generated
and

indicates that the output has been

disabled.

—

Table 1-4

Keypad functions (continued)

No.

Key

Function when pressed for less than one
second

Function when pressed for more than one
second

«
...
29
30
31
32
33
...
»

Содержание U1401B






















































































































































































Отзывы:

Нет отзывов