Agilent Technologies U1401B Скачать руководство пользователя страница 49

Страница: 49 / 181

Calibrator Output Operations

U1401B User’s and Service Guide

Constant Voltage Operation

The U1401B can generate a constant voltage output in two
different ranges, namely ±1.5 V and ±15 V.

To select the constant voltage output function:

Turn the rotary switch to any one of the

(constant

voltage output) positions.

Press

SHIFT

to access the shifted operations of the keypad.

The

annunciator will appear on the display.

Press

MODE

to cycle through ±1.5 V, ±15 V,

±1.5 V,

±15 V,

±1.5 V, and

±15 V output

modes. Select either ±1.5 V or ±15 V for constant output
(or steady output, as opposed to

autoscan

autoramp

outputs, which will be discussed under

“Memory

Generation”

on page 31), depending on the voltage range

you require.

•

Unlike the autoscan and autoramp modes, there is no
special annunciator on the display to indicate constant
voltage (CV) operation.

With the instrument in standby mode (you should see the

annunciator on the display; if not, press

OUTPUT

), you

can adjust the amplitude of the output by pressing

and

to select the digit to be adjusted, and then

pressing

and

to adjust the value of the selected

digit.

Press

OUTPUT

to start the source output. The

annunciator will appear on the display.

Содержание U1401B






















































































































































































Результаты поиска

Содержание U1401B

Отзывы:

Agilent Technologies U1401B, Руководство пользователя и сервисное руководство, Страница: 49 / 181

Результаты поиска

Содержание U1401B

Отзывы: