Agilent Technologies U1401B Скачать руководство пользователя страница 33

Страница: 33 / 181

Getting Started

U1401B User’s and Service Guide

The display at a glance

To view the full display (with all segments illuminated),
press

while turning the rotary switch from OFF to any

non- OFF position. After you are done viewing the full
display, press any key to resume the normal function,
depending on the rotary switch position.

The instrument will then enter power save mode if the auto
power- off (

) feature is enabled. To wake the

instrument up, perform the following steps:

Turn the rotary switch (knob) to the OFF position;

Then turn the rotary switch to any position other than
square wave output and press any key.

Figure 1-6

Full display

Содержание U1401B






















































































































































































Результаты поиска

Содержание U1401B

Отзывы:

Похожие инструкции для U1401B

Бренды по названию

Популярные бренды

Agilent Technologies U1401B, Руководство пользователя и сервисное руководство

Результаты поиска

Содержание U1401B

Отзывы:

Похожие инструкции для U1401B

Бренды по названию

Популярные бренды