Agilent Technologies U1401B Скачать руководство пользователя страница 168

Страница: 168 / 181

144

U1401B User’s and Service Guide

Specifications

General Specifications

Display

•

Both primary and secondary displays are 5-digit liquid crystal display (LCD)

with a maximum reading of 51,000 counts and automatic polarity indication.

Power Consumption

•

Charging battery: 9.3 VA typical

•

DC constant current at 25 mA, maximum load: 5.5 VA typical (on 24 V DC adapter) or
2.4 VA typical (on 9.6 V batteries)

•

Meter only: 1.8 VA typical (on 24 V DC adapter) or 0.6 VA typical (on 9.6 V batteries)

Power Supply

•

Rechargeable batteries — 1.2 V × 8 pieces (Ni-MH), no cadmium, lead or mercury.

•

External switching adapter, AC 100 V to 240V, 50/60 Hz input and DC 24 V/2.5 A output.

Operating Environment

•

Full accuracy at 0 °C to 40 °C (32 °F to 104 °F)

•

Full accuracy up to 80% Relative Humidity (RH) for temperature up to 31

C, decreasing

linearly to 50% RH at 40

Storage Compliance

•

–20 °C to 60 °C (–4 °F to 140 °F) with batteries removed.

Safety Compliance

•

IEC 61010-1:2001/EN61010-1:2001 (2nd Edition)

•

Canada: CAN/CSA-C22.2 No. 61010-1-04

•

USA: ANSI/UL 61010-1:2004

Measurement Category

•

CAT-II 150V, Pollution Degree 2 Environment.

EMC Compliance

•

IEC61326-2-1:2005/EN61326-2-1:2006

•

Canada: ICES/NMB-001:2004

•

Australia/New Zealand: AS/NZS CISPR11:2004

Measurement

•

3 times per second (AC+DC: 1 time per second)

•

1 time per second for frequency or duty cycle measurement. (>1 Hz)

•

0.25 to 1 time per second for Pulse Width measurements. (>1 Hz)

Common Mode Rejection Ratio (CMRR)

•

> 90 dB at DC, 50/60 Hz ± 0.1% (1 k

unbalanced)

Normal Mode Rejection Ratio (NMRR)

•

> 60 dB at DC, 50/60 Hz ± 0.1%

Temperature Coefficient

•

Input: 0.15 * (specified accuracy)/

C (from 0

C to 18

C or 28

C to 40

•

Output: ± (50ppm 0.5dgt)/

Содержание U1401B






















































































































































































Результаты поиска

Содержание U1401B

Отзывы:

Похожие инструкции для U1401B

Бренды по названию

Популярные бренды

Agilent Technologies U1401B, Руководство пользователя и сервисное руководство

Результаты поиска

Содержание U1401B

Отзывы:

Похожие инструкции для U1401B

Бренды по названию

Популярные бренды