Agilent Technologies U1401B Скачать руководство пользователя страница 25

Страница: 25 / 181

Getting Started

U1401B User’s and Service Guide

Product Overview

Slide switch

The slide switch has the following positions:

•

Charge

: Select this position to charge the batteries. Use the

AC adapter provided to charge this instrument.

•

: Select this position to enable only the measurement

functions.

•

M/S

: Select this position to enable both the measurement

and source functions.

Figure 1-1

The slide switch

Table 1-2

Slide switch functions

No.

Description

Function

External AC
adapter jack

Allows an external AC adapter to be connected to
provide power or charge the batteries.

CHARGE

Charges the batteries with an external AC adapter.

Enables only the measurement functions.

M/S

Enables both measurement and source functions.

Содержание U1401B






















































































































































































Результаты поиска

Содержание U1401B

Отзывы:

Похожие инструкции для U1401B

Бренды по названию

Популярные бренды

Agilent Technologies U1401B, Руководство пользователя и сервисное руководство

Результаты поиска

Содержание U1401B

Отзывы:

Похожие инструкции для U1401B

Бренды по названию

Популярные бренды