Agilent Technologies U1401B Скачать руководство пользователя страница 145

Страница: 145 / 181

Maintenance

U1401B User’s and Service Guide

125

When servicing the instrument, use only the specified
replacement parts.

Table 6- 2

will assist you in identifying some of the basic

problems.

Table 6-2

Troubleshooting

Malfunction

Identification of the problem

No LCD display after switching
ON

•

Check the position of the slide switch. Set it to the M or M/S position

•

Check the batteries. Recharge or replace the batteries if necessary

No beeper tone

Check the setup mode to see if the beeper has been disabled (“OFF”). Select the
desired driving frequency

Failed to measure current

Check fuse 1

No output signal when:

•

the

annunciator is

displayed.

•

the

OUTPUT

key is pressed

and the

annunciator

only appeared for a short
while before being replaced by
the

annunciator.

•

The batteries are low

•

Check the position of the slide switch. Set it to the M/S position

•

Check the external load to see whether the rated limit is exceeded.

•

Check whether the loop has a 24 V power. If yes, use the special yellow test lead for

mA simulation (see

Chapter 5

, “Simulation Mode for mA Output”)

•

Check fuse 2

No charging indication

•

Set the slide switch to the CHARGE position

•

Check the external adapter to see whether the output is 24 VDC and whether it is

properly plugged in to the charging terminal

•

Check the line power voltage (100 VAC to 250 VAC 47 Hz/63 Hz) and the power cord

Remote control failure

•

Make sure that the optical side of cable is connected to the instrument and the text

side of the connector cover should be facing up

•

Check the baud rate, parity, data bit, and stop bit (default settings: 9600, n, 8, 1)

•

Install the driver for IR-USB on your PC

Содержание U1401B






















































































































































































Результаты поиска

Содержание U1401B

Отзывы:

Agilent Technologies U1401B, Руководство пользователя и сервисное руководство, Страница: 145 / 181

Результаты поиска

Содержание U1401B

Отзывы: