Agilent Technologies U1401B Скачать руководство пользователя страница 70

Страница: 70 / 181

U1401B User’s and Service Guide

Making Measurements

Percentage scale of DC mA measurement

The percentage scale for 4 mA to 20 mA or 0 mA to 20 mA
is calculated based on the measured DC mA value.

Select the required range (4 mA to 20 mA or 0 mA to
20 mA) in the Setup mode (refer to

Chapter 4

, “Setting

the percentage scale readout”).

Turn the rotary switch to

Press

to select percentage scale display for DC mA

measurement.

Connect the red and black test leads to the positive and
negative input terminals respectively.

Probe the test points in series with the circuit and read
the display. The inset display in

Figure 3- 3

shows the

percentage scale reading representing 20 mA in the range
of 4 mA to 20 mA.

Содержание U1401B






















































































































































































Результаты поиска

Содержание U1401B

Отзывы:

Agilent Technologies U1401B, Руководство пользователя и сервисное руководство, Страница: 70 / 181

Результаты поиска

Содержание U1401B

Отзывы: