Agilent Technologies U1401B Скачать руководство пользователя страница 149 | Manualshive

Страница: 149 / 181

Agilent Technologies U1401B Скачать руководство пользователя страница 149

Performance Tests and Calibration

7

U1401B User’s and Service Guide

129

Closed-case electronic calibration

This instrument features closed- case electronic calibration.
In other words, no internal electro- mechanical adjustment is
required. This instrument calculates correction factors based
on the input reference signals you feed into it during the
calibration process. The new correction factors are stored in
non- volatile EEPROM memory until the next calibration
(adjustment) is performed. The contents of the non- volatile
EEPROM memory will not change even when the power is
switched off.

Agilent Technologies’ calibration services

When your instrument is due for calibration, contact your
local Agilent Service Center to inquire about recalibration
services.

Calibration interval

A one- year calibration interval is adequate for most
applications. Accuracy specifications are warranted only if
calibration is performed at regular intervals. Accuracy
specifications are not warranted beyond the one- year
calibration interval. Agilent does not recommend extending
calibration intervals beyond 2 years for any application.

«
...
147
148
149
150
151
...
»

Содержание U1401B






















































































































































































Отзывы:

Нет отзывов