Agilent Technologies U1401B Скачать руководство пользователя страница 150 | Manualshive

Страница: 150 / 181

Agilent Technologies U1401B Скачать руководство пользователя страница 150

130

U1401B User’s and Service Guide

7

Performance Tests and Calibration

Other recommendations for calibration

Specifications are only guaranteed within the specified
period from the last calibration. Agilent recommends that
readjustment should be performed during the calibration
process for best performance. This will ensure that the
Handheld Multi- Function Calibrator/Meter remains within its
specifications. This calibration criterion provides the best
long- term stability.

During performance verification tests, only the performance
data is collected; these tests do not guarantee that the
instrument will remain within the specified limits. The tests
are only for identifying the functions which need adjustment.

Environmental conditions

Calibration or verification tests should be performed under
laboratory conditions where the ambient temperature or
relative humidity can be controlled.

Warm up

Allow at least 20 minutes for the intrument to warm- up
before performing calibration. After being exposed or stored
in a high humidity (condensing) environment, a relatively
longer recovery period is required.

«
...
148
149
150
151
152
...
»

Содержание U1401B






















































































































































































Отзывы:

Нет отзывов