manualshive.com logo in svg

YOKOGAWA DL850 ScopeCorder, User Manual, Page: 80 / 190

Share
Download
YOKOGAWA DL850 ScopeCorder User Manual Download Page 80

3.15  Connecting a Cable to the CAN Bus Monitor 

Module

To monitor CAN bus signals, connect a cable to the CAN bus monitor module’s D-sub connector.

Connector Pinout

The pinout of the D-sub connector (9 pin, male) is shown below.

 

 

Pinout

1

5

6

9

Pin No.

Signal

Function

1

(NC)

Not used (can not be connected to)

2

CAN_L

CAN low signal

3

GND

Ground

4

(NC)

Not used (can not be connected to)

5

(NC)

Not used (can not be connected to)

6

GND

Ground

7

CAN_H

CAN high signal

8

(NC)

Not used (can not be connected to)

9

(NC)

Not used (can not be connected to)

*  One-inch screws (number 4-40 UNC) are used.

Note

The connector shell is connected to GND. Additionally, GND and the connector shell are isolated from the 
electric potential of the DL850/DL850V case (earth).

 

CAUTION

Applying a voltage greater than the maximum input voltage may damage the input section.

Connecting the Cable (Signal wires)

When you connect a cable to the D-sub connector, be sure to tighten the screws to ensure that the 
cable is connected securely.

 

CAN bus monitor module

720240 (CAN MONITOR)

Cable

Screws

3-39

IM DL850-03EN

Making Preparations for Measurements

1

2

3

4

5

6

App

Index

Summary of Contents for DL850 ScopeCorder































































































































































































Reviews:

No comments