YOKOGAWA DL850 ScopeCorder User Manual Download Page 136

Page: 136 / 190

6-28

IM DL850-03EN

Item

Specifications

Temperature coefficient

[Voltage measurement]

Zero point:

Gain:

±(0.01% of 10 div)/°C (Typical

)

±(0.02% of 10 div)/°C (Typical

)

Reference junction compensation

accuracy (when the input terminal

temperature is balanced)

K, E, J, T, L, U, N:

R, S, B, W:

Au7Fe:

±1°C

±1.5°C

±1K

Bandwidth limit

[Temperature measurement]

[Voltage measurement]

(Digital analog filter)

Select from OFF, 30 Hz, 8 Hz, and 2 Hz + 150 Hz secondary

analog filter

Select from OFF, AUTO, 4 kHz, 400 Hz, or 40 Hz.

Cutoff characteristics: −12 dB/OCT (Typical,

setting other than

AUTO)

Cutoff frequency (fc) when set to AUTO (701262 only)

Sample Rate

Cutoff Frequency (fc)

100 kS/s or higher 40 kHz
100 S/s to 50 kS/s

40% of the sample rate

50 S/s or less

20 Hz

Cutoff characteristics for AUTO: −65 dB at 2 × fc (Typical

)

Table of cutoff frequency

characteristics of the

anti-aliasing filter (AAF)

When the filter is set to Auto, the anti-aliasing filter and low-pass filter are automatically set

according to the sample rate.

Sample Rate

AAF

Low-Pass Filter

100 kS/s

40 kHz

OFF

50 kS/s

20 kHz

OFF

20 kS/s

8 kHz

OFF

10 kS/s

4 kHz

5 kS/s

2 kHz

4 kHz

2 kS/s

800 Hz

4 kHz

1 kS/s

400 Hz

500 S/s

200 Hz

400 Hz

200 S/s

80 Hz

400 Hz

100 S/s

40 Hz

50 S/s

20 Hz

40 Hz

20 S/s to 5 S/s

20 Hz

40 Hz

2 S/s or less

20 Hz

40 Hz

Ext sample

40 kHz

OFF

1 Value measured under standard operating conditions (section 19.11).
2 Does not include the reference junction temperature compensation accuracy.

3 This module supports Au7Fe with 0.07% metal content with respect to gold.

6. Typical value represents a typical or average value. It is not strictly warranted.

WARNING

• Do not apply input voltage exceeding the maximum input voltage or allowable common

mode input voltage.

• To prevent the possibility of electric shock, be sure to furnish protective earth grounding of

the DL850/DL850V.

• To prevent the possibility of electric shock, be sure to fasten the module screws.
Otherwise, the electrical and mechanical protection functions will not be activated.

6.13 Module Specifications

Summary of Contents for DL850 ScopeCorder































































































































































































Search results

Summary of Contents for DL850 ScopeCorder

Reviews:

YOKOGAWA DL850 ScopeCorder, User Manual, Page: 136 / 190

Search results

Summary of Contents for DL850 ScopeCorder

Reviews: