manualshive.com logo in svg

YOKOGAWA DL850 ScopeCorder, User Manual, Page: 142 / 190

Share
Download
YOKOGAWA DL850 ScopeCorder User Manual Download Page 142

6-34

IM DL850-03EN

Item

Specifications

Precautions

•  Highly sensitive measurements are made in the µ V level in strain measurements. 

Therefore, take measures against noise at the strain sensor perimeter, bridge head, and 

cable wiring.

•  Depending on the noise environment, an error may result in the balance. Check the 

influence before making measurements.

• The bridge head specified by YOKOGAWA has high noise resistance.

•  When executing shunt calibration, be sure to calculate the shunt resistance in advance, 

and execute it in a range so that the measured values do not exceed the range even when 

the shunt resistance is ON.

•  Some of the strain gauge sensors and bridge heads made by other manufacturers 

do not have sensing wires connected. (No such problems with bridge heads made by 

YOKOGAWA.) If such products are used, an error may result in the bridge voltage leading 

to measurement errors, because sensing does not work effectively. Perform sensing as 

close to the bridge head as possible. (There is no conversion cable for sensing on D-Sub 

connector types.)

• The connector shell is connected to the case potential.

•  When a bridge head (701957 or 701958) is used, the connector shell, cable shield, and the 

bridge head case are all connected to the case potential of the DL850/DL850V.

•  When a bridge head (701957 or 701958) is used, the floating GND is connected to the 

bridge head case inside the bridge head.

• Be sure to execute balancing again when you change the range or the bridge voltage.

1  Value measured under standard operating conditions.
2  The typical value is a representative or standard value. It is not strictly warranted.

Module front View

1

2

3

4

5

6

7

8

9

1: Floating common

2: Sense- (positive bridge voltage sensing)

3: Shuntcal- (negative shunt signal)

4: S (positive shunt signal)

5: Sense+ (positive bridge voltage sensing)

6: Bridge- (negative bridge voltage)

7: Input- (negative measurement signal)

8: Input+ (positive measurement signal)

9:  (positive bridge voltage)

 

WARNING

•  Do not apply input voltage exceeding the maximum input voltage or allowable common 

mode input voltage.

•  To prevent the possibility of electric shock, be sure to furnish protective earth grounding of 

the DL850/DL850V.

•  To prevent the possibility of electric shock, be sure to fasten the module screws.
  Otherwise, the electrical and mechanical protection functions will not be activated.
•   Avoid continuous connection under an environment in which the surge voltage may occur.

6.13  Module Specifications

Summary of Contents for DL850 ScopeCorder































































































































































































Reviews:

No comments