manualshive.com logo in svg

YOKOGAWA DL850 ScopeCorder, User Manual, Page: 55 / 190

Share
Download
YOKOGAWA DL850 ScopeCorder User Manual Download Page 55

3.5  Connecting Probes

Connecting Probes

Connect the probes (or other input cables such as BNC cables) to any of the input terminals of the 

following modules. The input impedance is 1 MΩ ± 1 % and approximately 35 pF.

•  High-Speed 100 MS/s, 12-Bit Isolation Module:            720210 (HS100M12)

•  High-Speed 10 MS/s, 12-Bit Isolation Module:            701250(HS10M12)

•  High-Speed High-Resolution 1 MS/s, 16-Bit Isolation Module:  701251 (HS1M16)

•  High-Speed 10 MS/s, 12-Bit Non-Isolation Module:         701255 (NONISO_10M12)

•  Acceleration/Voltage Module (with AAF):                701275 (ACCL/VOLT)

•  Frequency Module: 

                701280 (FREQ)

 

 

WARNING

•  When connecting a device under measurement to the instrument, be sure to turn off the 

device. It is extremely dangerous to connect or remove measurement leads while the 

device under measurement is on.

Precautions to Be Taken When Using the Modules

•  Do not apply input voltage exceeding the maximum input voltage, withstand voltage, or 

allowable surge voltage.

•  To avoid electric shock, be sure to ground the instrument.

•  To prevent the possibility of electric shock, be sure to fasten the module screws. Otherwise, 

the electrical protection function and the mechanical protection function will not be 

activated.

•  Do not leave the instrument connected to devices in an environment that may be subject to 

voltage surges.

•  Use only specified cables. It is extremely dangerous to use cables that do not meet the 

safety standards. (Especially when you are handling high voltages of 42 V or more.)

•  When measuring high voltages using the 720210 (HS100M12), 701250 (HS10M12), or 

701251 (HS1M16), use an isolated probe (the 700929 or 701947), 1:1 safety cable (a 

combination of the 701901 and 701954), or differential probe (700924).

•  The BNC portion of the 10 MHz passive probe (701940) is metal, so if you use it with 

isolated input (the 720210 (HS100M12), 701250 (HS10M12), 701251 (HS1M16), 701275 

(ACCL/VOLT), or 701280(FREQ)), for safety, be sure to only use it with voltages at or 

below 42 V. (Do not connect voltage above 42 V to both the High and Low sides.)For non-

isolated inputs (701255 (NONISO_10M12), etc.), fasten the module screws.

•  When you apply high voltages to the 701280 (FREQ), use an isolated probe (the 700929 or 

701947).

In Using the High Voltage Differential Probes

Be sure to connect the GND lead of a differential probe (the 700924 or 700925) to the 
functional ground terminal on the right side panel of the instrument. Otherwise, high voltage 
may appear at the BNC connector making it dangerous.

3-14

IM DL850-03EN

Summary of Contents for DL850 ScopeCorder































































































































































































Reviews:

No comments