YOKOGAWA DL850 ScopeCorder User Manual Download Page 190

Page: 190 / 190

App-29

IM DL850-03EN

Appendix

App

Index

Item

Specifications

Compatible probes/

cables

Connection cable (for high voltage 1:1): Recommended 1

701901 (isolated type BNC-safety alligator clip adapter ×2: For measuring 850 V (DC+ACpeak) or

less), 701954 (alligator clip (dolphin type) red/black 2-piece set) is required separately

Voltage probe: Recommended 2

700929 (10:1 safety probe).20 to 45 pF: For measuring 1000 Vpeak or less

701947 (100:1 probe).15 to 45 pF: For measuring 1000 Vpeak or less

Current probe (power can be supplied from the DL850/DL850V. Option)

700937 (15 A), 701930 (150 A), 701931 (500 A), 701933 (30 A)

1 Value measured under standard operating conditions.

Combined with the 700929 or 701947

700929

701947

701901

701954

Combined with the 701954

Direct input (cable that does not comply with the safety standards)

BNC

Withstand voltage: 3700 Vrms for 1 minute

Allowable transient surge voltage: ±5200 Vpeak

(between earth and input)

10 The typical value is a representative or standard value. It is not strictly warranted.

WARNING

• When applying high voltage using this module, use the 1:1 safety cable (combination of

701901 and 701954) or the isolated probe (700929 or 701947).

• Note that the overvoltage tolerance of the low and high sides of this module may differ

depending on the combination of the connected probe, measurement lead, and clip.

• Do not apply input voltage exceeding the maximum input voltage, withstand voltage, or

allowable surge voltage.

• To prevent the possibility of electric shock, be sure to furnish protective earth grounding of

the DL850/DL850V.

• To prevent the possibility of electric shock, be sure to fasten the module screws. Otherwise,

the electrical and mechanical protection functions will not be activated.

• Avoid continuous connection under an environment in which the surge voltage may occur.

Appendix 6 High-Voltage 100 kS/s, 16-Bit Isolation Module (with RMS) (701260) Specifications

Summary of Contents for DL850 ScopeCorder































































































































































































Search results

Summary of Contents for DL850 ScopeCorder

Reviews:

YOKOGAWA DL850 ScopeCorder, User Manual, Page: 190 / 190

Search results

Summary of Contents for DL850 ScopeCorder

Reviews: