manualshive.com logo in svg

YOKOGAWA DL850 ScopeCorder, User Manual, Page: 48 / 190

Share
Download
YOKOGAWA DL850 ScopeCorder User Manual Download Page 48

Note

•  You can install up to four 720210 modules, and these modules must be installed in the top slots.
•  You can install a total of two 720240 CAN bus monitor modules (CAN MONITOR) and 720241 CAN & LIN 

bus monitor modules (CAN & LIN). These monitor modules can only be installed in slots 7 and 8.

Removal

1.

  Make sure that the instrument’s power switch is off.

2.

  Loosen the two screws that are fastened to the input module.

3.

  Hold the two handles at the top and bottom of the input module, and pull it out.

About the High-speed, 100 MS/s, 12-bit Isolated Module

Safety Precautions for Laser Products

The High-Speed 100 MS/s, 12-Bit Isolation Module (720210 (HS100M12)) uses an internal laser light 
source. The 720210 (HS100M12) is a class 1 laser product as defined by IEC60825-1: Safety of Laser 
Products—Part1: Equipment Classification.

High-Speed 100 MS/s, 12-Bit Isolation Module  (720210 (HS100M12))

The following information is printed on the side.

 

 

DL850/DL850V

The following information is printed on the top.

 

 

3.3  Installing Input Modules

3-7

IM DL850-03EN

Making Preparations for Measurements

1

2

3

4

5

6

App

Index

Summary of Contents for DL850 ScopeCorder































































































































































































Reviews:

No comments