manualshive.com logo in svg

YOKOGAWA DL850 ScopeCorder, User Manual, Page: 76 / 190

Share
Download
YOKOGAWA DL850 ScopeCorder User Manual Download Page 76

What to Prepare

Wiring

  Remove approximately 7 mm of the insulation from the ends of the wires.

  Electrical wire:  0.20 mm

2

 to 1.00 mm

2

 recommended (solid wire or thin stranded wire). AWG 

size: 24-18.

 

   

Approx. 7 mm

Flat-blade Screwdriver

    Tip size:   0.4 mm (thickness) × 2.5 mm (width)
    Shape:    DIN5264-A (Use a straight driver.)

Connecting Wires to the Terminal Block

First, turn off the DL850/DL850V. Make sure that the other end of the wire that you are connecting to 
the terminal block is not connected to the device under measurement, or make sure that the device 
under measurement that you are going to connect to is turned off.

1.

  Insert the flat-blade screwdriver into the screwdriver insertion hole right next to the wire 

insertion hole.

If you do not insert the flat-blade screwdriver into the hole firmly, the wire insertion hole will not open.

2.

  Insert the wire that you prepared into the wire insertion hole.

Insert the wire until it reaches the back of the wire insertion hole.

3.

  Pull the flat-blade screwdriver out of the screwdriver insertion hole.

When you pull out the flat-blade screwdriver, hold the wire in place so that it does not come out with the 
screwdriver.

4.

  Pull lightly on the wire to make sure that it doesn’t come out.

After you have finished connecting the wires, turn on the DL850/DL850V and the device under 

measurement.

 

 

Wire

Flat-blade screwdriver

Terminal block

Module: 720220 (16CH VOLT)

Wire insertion hole

Screwdriver 

insertion hole

Note

Removing and Attaching the Terminal Block

It is normally not necessary to remove the terminal block, but it is possible to do so.

  Removal

  Push terminal block release levers 1 and 2 to their release positions, and pull out the terminal block.

  Attachment

  Push terminal block release levers 1 and 2 to their lock positions, and insert the terminal block. Push the 

terminal block firmly all the way to the back. However, the terminal block will not go all the way to the back 
if it is upside down. Do not try to force the terminal block all the way to the back.

 

     

Release lever 1

Release lever 2

Hold

Release

Removing

Attaching

3.13  Connecting Wires to the 16-CH Voltage Input Module

3-35

IM DL850-03EN

Making Preparations for Measurements

1

2

3

4

5

6

App

Index

Summary of Contents for DL850 ScopeCorder































































































































































































Reviews:

No comments