6-41
IM DL850-03EN
Specifications
1
2
3
4
5
6
App
Index
High-Speed 100 MS/s, 12-Bit Isolation Module (720210) Specifications
Item
Specifications
Standard operating conditions
Temperature:
Humidity:
23 ±5°C
20 to 80% RH
After a 30-minute warm-up and after calibration
Effective measurement range
20 div (display range: 10 div)
Number of input channels
2
Input coupling
AC, DC, and GND
Maximum sample rate
100 MS/s
Input format
Isolated unbalanced
Frequency characteristics
1
(−3 dB point when sine wave of amplitude ±3 div is applied) DC to 20 MHz
Voltage-axis sensitivity setting
10 mV/div to 20 V/div (1-2-5 steps) (when using 1:1 probe attenuation)
Maximum input voltage
(at a frequency of 1 kHz or less)
Combined with the 700929 (10:1) or 701947 (100:1):
2
1000 V (DC+ACpeak) CAT II
Direct input (cable that does not comply with the safety standards):
4
200 V (DC+ACpeak)
Maximum allowable common
mode voltage
(at a frequency of 1 kHz or less)
Working voltage of safety standard
Combined with the 700929 (10:1) or 701947 (100:1):
3
1000 Vrms (CAT II)
Direct input (cable that does not comply with the safety standards):
5
42 V (DC+ACpeak) (CAT II, 30 Vrms)
Vertical (voltage) axis accuracy
DC accuracy
1
10 mV/div to 20 V/div: ±(0.5% of 10 div)
Input connector
BNC connector (isolated type)
Input impedance
1 MΩ ± 1%, approx. 35 pF
−3 dB point when AC coupled
low frequency attenuation point
10 Hz or less (1 Hz or less when using the 700929, 0.1 Hz or less when using the 700929)
Common mode rejection ratio
80 dB (50/60 Hz) or more (Typical
6
)
Residual noise level
(Input section shorted)
±1.1 mV or ±0.15 /div whichever is greater (Typical
6
)
Withstand voltage
1500 Vrms for 1 minute (across each terminal and earth) (60 Hz)
Insulation resistance
500 VDC, 10 MΩ or more (across each input terminal and earth)
A/D conversion resolution
12 bit (150 LSB/div)
Temperature coefficient
Zero point:
Gain:
10 mV/div to 20 V/div: ±(0.1% of 10 div)/°C(Typical
6
)
±(0.05% of 10 div)/°C(Typical
6
)
Bandwidth limit
Select from OFF, 2 MHz, 1.28 MHz, 640 kHz, 320 kHz, 160 kHz, 80 kHz, , 40 kHZ, 20 kHz,
and 10 kHz
Cut-off characteristics:
−12 dB/OCT (when 2 MHz, Typical
6
)
Probe attenuation setting
Voltage probe:
Current probe:
1:1, 10:1, 100:1, 1000:1
10 A:1 V (for the 700937/701933), 100 A: 1 V (for the 701930/701931)
1 Value measured under standard operating conditions.
H
L
Combined with the 700929 or 701947
2
700929
701947
H
L
Direct input (cable that does not comply with the safety standards)
4
5
BNC
Withstand voltage: 1500 Vrms for 1 minute
Allowable transient surge voltage (between earth and input): ±2100 Vpeak
3
6 Typical value represents a typical or average value. It is not strictly warranted.
6.13 Module Specifications