manualshive.com logo in svg

YOKOGAWA DL850 ScopeCorder, User Manual, Page: 64 / 190

Share
Download
YOKOGAWA DL850 ScopeCorder User Manual Download Page 64

•  For the 701267 (HV (with RMS))

  Maximum input voltage (at a frequency of 1 kHz or less)
  •   Combination of 758933 measurement leads and 701954 alligator clips

3

    850 V (DC + ACpeak)
  •  Direct input (cable that does not comply with the safety standards)

6

    42 V (DC + ACpeak)
  Maximum allowable common mode voltage (at a frequency of 1 kHz or less)
  •   Combination of 758933 measurement leads and 701954 alligator clips

5

    (Use caution because the overvoltage tolerance differs between the low and high sides.)
    700 Vrms (CAT II) on the H side,

4

 400 Vrms (CAT II)

5

 on the L side

  •  Direct input (cable that does not comply with the safety standards)

7

    42 V (DC + ACpeak)  (CAT II, 30 Vrms)

 

     

H

L

1

2

(Red)

(Black)

(Red)

(Black)

(Red)

(Black)

H

L

3

5

758933

701954

4

H

L

6

7

For the 701261, 701262, 701265

For the 701267

With the 758933 and 701954

Direct input (cable that does not comply 

with the safety standards)

Input 

terminal

Input 

terminal

Input 

terminal

Over-Range Indication

If over-range is indicated, the DL850/DL850V may be receiving a voltage higher than the 

observed waveform or measured waveform values. To prevent electric shock, change the 

vertical scale with the SCALE knob so that the entire amplitude of the waveform is displayed 

within the waveform display area, and check the input voltage level.

 

     

Over-range indication

Indicates the number of the channel that over-range is occurring on.

Channel indication when over-range is occurring on multiple channels

Indicates the smallest number among the channels that over-range is 

occurring on.

3.7  Connecting Measurement Leads

3-23

IM DL850-03EN

Making Preparations for Measurements

1

2

3

4

5

6

App

Index

Summary of Contents for DL850 ScopeCorder































































































































































































Reviews:

No comments