manualshive.com logo in svg

YOKOGAWA DL850 ScopeCorder, User Manual, Page: 49 / 190

Share
Download
YOKOGAWA DL850 ScopeCorder User Manual Download Page 49

Laser Specifications

Center wavelength:  850 nm

Pulse width:  

≤ 10 ms (100 MHz), ≤ 2.5 ns (2 GHz)

Output:  

≤ 1 mW

If the instrument is used in a manner not specified in this manual, the protection provided by the 
instrument may be impaired. YOKOGAWA assumes no liability for the customer’s failure to comply 
with these warnings and requirements.

LEDs on the Frequency Module

On the front panel of the frequency module (701280 (FREQ)) are LEDs for each channel. These LEDs 
allow you to check the input condition of the pulse.

 

ACT

OVER

ACT

OVER

701280 (FREQ)

LED

Green:  Pulses are being received.

Red: 

The input voltage range has 

 

been exceeded.

Off: 

Pulses are not being received.

Note

•  The LEDs on the frequency module illuminates in green when pulse is applied and red when the input 

voltage level is over range. It is independent of the start/stop condition of waveform acquisition of the 
DL850/DL850V.

•  When the preset of the frequency module is set to EM Pickup (electromagnetic pickup), the LED will not 

illuminate in red when the range is exceeded.

  For information about presets, see section 1.7, “Configuring Frequency, Revolution, Period, Duty Cycle, 

Power Supply Frequency, Pulse Width, Pulse Integration, and Velocity Measurements,” in the user’s 
manual.

3.3  Installing Input Modules

3-8

IM DL850-03EN

Summary of Contents for DL850 ScopeCorder































































































































































































Reviews:

No comments