manualshive.com logo in svg

YOKOGAWA DL850 ScopeCorder, User Manual, Page: 107 / 190

Share
Download
YOKOGAWA DL850 ScopeCorder User Manual Download Page 107

5-7

IM DL850-03EN

External Signal I/O

1

2

3

4

5

6

App

Index

External Start/Stop Input (EXT I/O)

You can use an external signal to start and stop the DL850/DL850V.

External Start/Stop Input Terminal

The External Start/Stop Input terminal and the GO/NO-GO I/O terminal are the same terminal. This 
terminal is used as an external start/stop input when the GO/NO-GO determination I/O function is not 
used (when on the GO/NO-GO menu, Mode is set to OFF).

Specifications

  The connector uses an RJ-11 modular jack. Connect the separately sold 720911 cable to the 

connector.

 

 

6

1

1

Pin no.

Signal

2

3

4

5

6

EXT  EVENT  IN

START  IN

NC (no connection)

NC (no connection)

Connector on 

the DL850/DL850V

Starts on low edge, stops on high

GND

NC (no connection)

EXT I/O

Manual event. Event input occurs on low edge.

  Input level: TTL (0 to 5 V)

Circuit Diagram for External Start/Stop Input

 

+5 V

120 Ω

LCX14

4.7 kΩ

100 pF

2

(pin no.)

High

Low

START

STOP

+5 V

120 Ω

LCX14

4.7 kΩ

100 pF

2

• Contact input is possible

5

Close to start, 

open to stop

Note

•  Low and high edges are used to detect starts and stops.
•  You can select whether to enable high edges (stops) in the external start/stop signal or disable. For 

information about how to do so, see section 18.8, “Configuring the Environment Settings,” in the user’s 
manual.

5.5  GO/NO-GO Determination I/O and External Start/Stop Input (EXT I/O)

Summary of Contents for DL850 ScopeCorder































































































































































































Reviews:

No comments