YOKOGAWA DL850 ScopeCorder User Manual Download Page 47

Page: 47 / 190

Types of Input Modules

The following 14 types of input modules are available.

High-Speed 100 MS/s, 12-Bit Isolation Module

720210 (HS100M12)

High-Speed 10 MS/s, 12-Bit Isolation Module

701250 (HS10M12)

High-Speed High-Resolution 1 MS/s, 16-Bit Isolation Module:

701251 (HS1M16)

High-Speed 10 MS/s, 12-Bit Non-Isolation Module

701255 (NONISO_10M12)

High-Voltage 100 kS/s, 16-Bit Isolation Module (with RMS)

701267 (HV (with RMS))

Universal (Voltage/Temp.) Module

701261 (UNIVERSAL)

Universal (Voltage/Temp.) Module (with AAF)

701262 (UNIVERSAL (AAF))

Temperature, High Precision Voltage Isolation Module

701265 (TEMP/HPV)

Strain Module (NDIS)

701270 (STRAIN_NDIS)

Strain Module (DSUB, Shunt-Cal)

701271 (STRAIN_DSUB)

Acceleration/Voltage Module (with AAF)

701275 (ACCL/VOLT)

Frequency Module

701280 (FREQ)

16-CH Voltage Input Module

720220 (16CH VOLT)

16-CH Temperature/Voltage Input Module

720221 (16CH TEMP/VOLT)

Logic Input Module

720230 (LOGIC)

CAN Bus Monitor Module

720240 (CAN MONITOR)

CAN & LIN Bus Monitor Module

720241 (CAN & LIN)

* The CAN bus monitor module and CAN & LIN bus monitor module can be used on the DL850V. It cannot be

used on the DL850.

Precautions to Be Taken When Installing or Removing Input

Modules

If you replace one installed input module with another, the settings for the channel will be reset to their
defaults when the power is turned on. If you want to keep the settings, specify a save destination and
save them.

Installation Procedure of Modules

Make sure that the power switch on the left side panel of the instrument is turned off.

Check the channel number displayed on the input module installation slot on the right side

panel of the instrument, and then install the input module along the guide.

Holding the handles on the top and bottom of the input module, press hard until it clicks in

place. If there is a cover plate on the slot in which to install the module, remove the cover plate,

first.

Firmly fasten the screws that came with the instrument in two places: the top and bottom of the

input module. (screw tightening torque: 0.6 N•m)

Turn the instrument’s power switch on.

In the overview screen, check that the name of the module that you installed is displayed

correctly at the appropriate slot. If it is not correct, remove the module according to the steps

in “Removal” shown below, and reinstall the module according to steps 1 to 3 shown above. To

display the overview screen, see section 19.4,

“

Viewing System Information (Overview),” in the

user’s manual.

Guide

3.3 Installing Input Modules

3-6

IM DL850-03EN

Summary of Contents for DL850 ScopeCorder































































































































































































Search results

Summary of Contents for DL850 ScopeCorder

Reviews:

YOKOGAWA DL850 ScopeCorder, User Manual, Page: 47 / 190

Search results

Summary of Contents for DL850 ScopeCorder

Reviews: