YOKOGAWA DL850 ScopeCorder User Manual Download Page 78 | Manualshive

Page: 78 / 190

YOKOGAWA DL850 ScopeCorder User Manual Download Page 78

CAUTION

• Correct measurements cannot be obtained when the positive and negative thermocouple

leads are connected in reverse.

• Immediately after connecting the thermocouple, the heat balance may be disturbed at

the input terminal section and may cause measurement errors. Therefore, wait about ten

minutes before making a measurement.

• In an environment where the air from the air conditioning is directly applied to the input

terminals or where there are effects from a heat source, the heat balance may be disturbed

at the input terminal section and cause measurement errors.

When making measurements in this type of environment, take preventive measures such

as changing the position.

What to Prepare

Thermocouple or Wiring

Remove approximately 7 mm of the insulation from the ends of the thermocouple or wires.

Electrical wire: 0.14 mm

2

to 1.5 mm

2

recommended (solid wire or thin stranded wire). AWG size:

26-16.

Approx. 7 mm

Flat-blade Screwdriver

Tip size: 0.6 mm (thickness) × 3.5 mm (width)
Screw tightening torque: 0.5 to 0.6 N•m)

Connecting Wires to the Terminal Block

First, turn off the DL850/DL850V. Make sure that the other end of the wire that you are connecting to
the terminal block is not connected to the device under measurement, or make sure that the device
under measurement that you are going to connect to is turned off.

When you first use the 16-CH scanner box, follow the procedure from step 3.

1.

Remove the protection cover screw using a screwdriver.

2.

Pull the protection cover up, and pull it out from the guide hole.

Guide hole

Protection cover screw

3.

Loosen the terminal block screw using a flat-blade screwdriver.

4.

Insert the thermocouple or wire that you prepared into the wire insertion hole.

Insert the thermocouple or wire until its end reaches the back of the wire insertion hole.

5.

Tighten the terminal block screw using a flat-blade screwdriver.

Terminal block

Wire insertion hole

Flat-blade Screwdriver

Wire

6.

Pull lightly on the wire to make sure that it doesn’t come out.

3.14 Connecting Wires to the 16-CH Temperature/Voltage Input Module

3-37

IM DL850-03EN

Making Preparations for Measurements

1

2

3

4

5

6

App

Index

«
...
76
77
78
79
80
...
»

Summary of Contents for DL850 ScopeCorder































































































































































































Reviews:

No comments