manualshive.com logo in svg

YOKOGAWA DL850 ScopeCorder, User Manual, Page: 8 / 190

Share
Download
YOKOGAWA DL850 ScopeCorder User Manual Download Page 8

vi

IM DL850-03EN

Input Modules (Sold Separately)

To make sure that an input module is the module that you ordered, check the module name written on 
it.

MODEL

Name

Abbreviation

701250

High-Speed 10 MS/s, 12-Bit Isolation Module

HS10M12

701251

High-Speed High-Resolution 1 MS/s, 16-Bit Isolation 

Module

HS1M16

701255

High-Speed 10 MS/s, 12-Bit Non-Isolation Module

NONISO_10M12

701267

High-Voltage 100 kS/s, 16-Bit Isolation Module (with RMS) HV (with RMS)

701261

Universal (Voltage/Temp.) Module

UNIVERSAL

701262

Universal (Voltage/Temp.) Module (with AAF)

UNIVERSAL(AAF)

701265

Temperature, High Precision Voltage Isolation Module

TEMP/HPV

701270

Strain Module (NDIS)

STRAIN_NDIS

701271

Strain Module (DSUB, Shunt-Cal)

STRAIN_DSUB

701275

Acceleration/Voltage Module (with AAF)

ACCL/VOLT

701280

Frequency Module

FREQ

720210

High-Speed 100 MS/s, 12-Bit Isolation Module

HS100M12

720220

16-CH Voltage Input Module

16CH VOLT

720221

16-CH Temperature/Voltage Input Module

16CH TEMP/VOLT

720230

Logic Input Module

LOGIC

720240

CAN Bus Monitor Module*

CAN MONITOR

720241

CAN & LIN Bus Monitor Module*

CAN & LIN

*  The CAN bus monitor module and CAN & LIN bus monitor module can be used on the DL850V. It 

cannot be used on the DL850.

 

MODEL

NO.

SUFFIX

Made  in  Japan

MODEL

NO.

SUFFIX

Made  in  Japan

701250

HS10M12

Top line: 

 Model

Bottom line:  Abbreviation

The location varies depending on the module.

In this manual, input modules are referred to by their model names and abbreviations.
For example, the High-Speed 10 MS/s, 12-Bit Isolation Module is referred to as the 701250 (HS10M12). 
However, if a module has already been referred to previously, it may be referred to only by its model 
name (for example, 701250).

Note

To use the DL850/DL850V with 701250 and 701255 modules shipped between August 2006 and June 2007, 
you must update the module firmware. If error code 916 appears when you turn on the DL850/DL850V, it may 
be necessary to update the firmware of the aforementioned modules. Prepare the module serial numbers, 
and contact your nearest YOKOGAWA dealer. The dealer will update the module firmware for a fee.

Checking the Contents of the Package

Summary of Contents for DL850 ScopeCorder































































































































































































Reviews:

No comments