manualshive.com logo in svg

YOKOGAWA DL850 ScopeCorder, User Manual, Page: 154 / 190

Share
Download
YOKOGAWA DL850 ScopeCorder User Manual Download Page 154

6-46

IM DL850-03EN

1  Value measured under standard operating conditions.
2  Does not include the reference junction temperature compensation accuracy.

3  This module supports Au7Fe with 0.07% metal content with respect to gold.

+

−

5

4

6  Typical value represents a typical or average value. It is not strictly warranted.

 

WARNING

•  When connecting a device under measurement to the instrument, be sure to turn off the 

device. It is extremely dangerous to connect or disconnect wires while the device under 
measurement is on.

Precautions to Be Taken When Using the Modules

•  To avoid electric shock, be sure to ground the instrument.
•  To prevent the possibility of electric shock, be sure to fasten the module screws. Otherwise, 

the electrical protection function and the mechanical protection function will not be 
activated.

Precautions to Be Taken When Using the 16-CH Scanner Box

•  Do not connect or disconnect the 16-CH scanner box or the cables that are connected to it 

while the power is on.

•  Do not apply input voltage exceeding the maximum input voltage, withstand voltage, or 

allowable surge voltage.

•  Do not leave the instrument connected to devices in an environment that may be subject to 

voltage surges.

•  To prevent electric shock, connect wires to the terminal block that match the voltage range 

that you are measuring.

•  Applying a voltage exceeding the value indicated below may damage the input section. 

If the frequency is above 1 kHz, damage may occur even when the voltage is below this 
value.

  Maximum input voltage (across the input terminals, + and −,

1

 at a frequency of 1 kHz or 

less)

    42 V (DC + ACpeak)
  Maximum allowable common

 

mode voltage (across the input terminals, + or −, and earth,

2

 

at a frequency of 1 kHz or less)

    42 V (DC + ACpeak) (CAT II, 30 Vrms)

•  The − input terminals of the sub channels are electrically insulated inside the scanner 

box. If you connect a wire that has a potential difference greater than 42 V (DC + ACpeak) 
between sub channels, the insulation may be damaged, which will lead to the 16-CH 
scanner box being damaged.

+

−

Input terminal

Ground

2

1

+

−

+

−

+

−

Wire insertion hole

Screwdriver insertion hole

Terminal block

Sub channel

CH 1

CH 2

CH 8

+

−

H

−

+

−

Terminal block

Sub channel

CH 9

CH 10

CH 16

6.13  Module Specifications

Summary of Contents for DL850 ScopeCorder































































































































































































Reviews:

No comments