manualshive.com logo in svg

YOKOGAWA DL850 ScopeCorder, User Manual, Page: 59 / 190

Share
Download
YOKOGAWA DL850 ScopeCorder User Manual Download Page 59

Precautions to Be Taken When Using Current Probes

When connecting the current probe to the probe power supply terminal on the right side panel, 
make sure that the current does not exceed the range shown below. Otherwise, the DL850/DL850V 
operation may become unstable due to the activation of the excessive current protection circuit of the 
power supply.

 

(Total current consumption for A through D) ≤ 1 A

If the terminals are named A through D

A

PROBE

POWER

(±12V DC      )

B

C

D

Specifications of the Probe Power Supply Terminals (Optional)

Item

Number of probes that can be used

4

Probes that can be used

Current probe (700937, 701930, 701931, and 701933)

Number of current probes that can be used

700937 (15 A): Up to 4
701930 (150 A): Up to 2
701931 (500 A): Up to 1
701933 (30 A): Up to 2

Supply voltage

±12 V, two outputs (up to 1 A total current)

When using the current probe, the number of probes that can be used is limited by the current 
generated by the device under measurement (current measured by the current probe). The measured 
versus consumed current characteristics of current probes that can be connected to the instrument are 
indicated below.

 

-250

-200

-150

-100

-50

-15

-10

-5

0

5

10

15

0

50

100

150

200

250

Current probe (700937)

Current consumption (mA)

Measured current (A)

Positive 

current

Negative 

current

-400

-300

-200

-100

-150

-100

-50

0

50

100

150

0

100

200

300

400

Current probe (701930)

Current consumption (mA)

Measured current (A)

Positive 

current

Negative 

current

AC (f = 50 Hz)

DC

AC (f = 50 Hz)

DC

-500

-400

-300

-200

-100

-500 -400 -300

0

100 200

500

0

100

200

300

400

500

Current consumption (mA)

Measured current (A)

Positive 

current

Negative 

current

-200 -100

300 400

Current probe (701931)

AC (f = 50 Hz)

DC

Current probe (701933)

Current consumption (mA)

Measured current (A)

600
500
400
300
200
100

0

-100
-200
-300
-400
-500
-600

Positive 

current

Negative 

current

AC (f = 50 Hz)

DC

-50 -40 -30 -20 -10

0

10

20

30

40

50

For details about each current probe, contact your nearest YOKOGAWA dealer.

3.5  Connecting Probes

3-18

IM DL850-03EN

Summary of Contents for DL850 ScopeCorder































































































































































































Reviews:

No comments