manualshive.com logo in svg

YOKOGAWA DL850 ScopeCorder, User Manual, Page: 117 / 190

Share
Download
YOKOGAWA DL850 ScopeCorder User Manual Download Page 117

6-9

IM DL850-03EN

Specifications

1

2

3

4

5

6

App

Index

Item

Specifications

LPF:

Cutoff frequency: 3 MHz to 0.2 Hz
Resolution:

3 MHz to 300 kHz, in steps of 20 kHz

Resolution:

298 kHz to 30 kHz, in steps of 2 kHz

Resolution:

29.8 kHz to 3 kHz, in steps of 200 Hz

Resolution:

2.98 kHz to 0.3 kHz, in steps of 20 Hz

Resolution:

298 Hz to 30 Hz, in steps of 2 Hz

Resolution:

29.8 Hz to 0.2 Hz, in steps of 0.2 Hz

HPF:

Cutoff frequency: 3 MHz to 20 Hz
Resolution:

3 MHz to 300 kHz, in steps of 20 kHz

Resolution:

298 kHz to 30 kHz, in steps of 2 kHz

Resolution:

29.8 kHz to 3 kHz, in steps of 200 Hz

Resolution:

2.98 kHz to 20 Hz, in steps of 20 Hz

BPF:

Center frequency: 3 MHz to 60 Hz
Resolution:

3 MHz to 120 kHz, in steps of 20 kHz

Resolution:

118 kHz to 12 kHz, in steps of 2 kHz

Resolution:

11.8 kHz to 1.2 kHz, in steps of 200 Hz

Resolution:

1.18 kHz to 60 Hz, in steps of 20 Hz

Bandwidth:

2, 1.5, 1 MHz, 500, 200, 150, 100, 50, 20, 15, 

10, 5, 2, 1.5, 1 kHz, 500, 200, 100 Hz (there 

are limits based on the center frequency)

Cutoff characteristic: –24 dB/Oct
Phase:

Nonlinear phase characteristicst

Interpolation:

Interpolation can be turned on and off.

Resolver:

The angle of rotation is computed from the carrier signal, sine signal, and cosine 

signal.
Supported carrier frequencies: 1 kHz to 20 kHz
Tracking filter band setting:  2 kHz, 1 kHz, 250 Hz, 100 Hz
Maximum measurable angular acceleration:

140000 rps

2

 (when the tracking filter is set to 2 kHz)

54000 rps

2

 (when the tracking filter is set to 1 kHz)

1800 rps

2

 (when the tracking filter is set to 250 Hz)

180 rps

2

 (when the tracking filter is set to 100 Hz)

Demodulation of the pulse width modulated (PWM) signal:

The PWM-modulated signal is integrated over the modulation period and converted 

into an analog signal.

Reactive power

The reactive power is computed from apparent power and effective power.

CAN ID detection

The frame of the CAN bus signal with the specified ID is detected.

Math source 

waveforms

• Analog channels 1 to 16 and the sub channels of scanner and CAN modules.

• Math results can be specified as sources of another channel.
•  However, you can only specify math results of channels whose numbers are smaller 

than the channel that you are specifying sources for.

Math delay

A uniform delay for each math operation, regardless of the number of math channels

Mean

The mean can be calculated on the math results.

Number of taps: 32 (fixed)

The calculation period changes automatically according to the DL850/DL850V sample 

rate.

Zoom Method

Zooming by 

Setting a 

Magnification

V Zoom is set in steps of 1, 2, or 5 to a value in the range of 10.00E–21 to 500.0E+18.

Zooming by 

Setting Upper and 

Lower Display 

Limits

Upper limit: 

±5.0000E+22; lower limit: ±1.0000E–23

6.5  Features

Summary of Contents for DL850 ScopeCorder































































































































































































Reviews:

No comments