YASKAWA VIPA System SLIO Manual Download Page 316

Page: 316 / 380

I-Device with S7 routing
S7 routing is not possible with the procedure above. S7 routing is only

possible if the I-Device and the higher-level I/O controller are configured

in the same network. The device names must not be identical. By using

identical names and extending the name of the I-Device with "-x", this is

detected internally and used appropriately for S7 routing.

13.7 TIA Portal - Option: Deployment PROFIBUS communication

13.7.1

Fast introduction

The PROFIBUS DP master must be configured in the

Project view

. Here the configuration

happens by the sub module X1 (MPI/DP) of the Siemens CPU.

To switch the interface X3 MPI(PtP) to PROFIBUS functionality you have

to activate the according bus functionality by means of a VSC storage

media from VIPA. By plugging the VSC storage card and then an overall

reset the according functionality is activated.

Chap. 4.16 ‘Deployment

storage media - VSD, VSC’ page 111

The configuration of the PROFIBUS DP master should be done with the following

approach:

Activating bus functionality by means of a VSC

Hardware configuration - CPU

Deployment as DP master

deployment as DP slave

Transfer of the entire project to the CPU

13.7.2

Activating bus functionality by means of a VSC

To use the MPI(PtP) interface X3 as PROFIBUS interface, the PROFIBUS functionality

must be activated by means of a VSC memory card from VIPA.

Plug the VSC memory card from VIPA.

‘Overview’ page 111

Execute an overall reset.

Chap. 4.13 ‘Overall reset’ page 105

The PROFIBUS functionality is enabled.

With activating the bus functionality "PROFIBUS DP master", the bus func-

tionality "PROFIBUS DP slave" is also enabled.

13.7.3

Hardware configuration - CPU

Perform a hardware configuration for the CPU.

Chap. 13.3 ‘TIA Portal - Hardware con-

figuration - CPU’ page 296

13.7.4

Deployment as PROFIBUS DP master

The hardware configuration described before was performed.

Overview

Steps of configuration

Proceeding

Precondition

VIPA System SLIO

Configuration with TIA Portal

TIA Portal - Option: Deployment PROFIBUS communication > Deployment as PROFIBUS DP master

HB300 | CPU | 013-CCF0R00 | en | 19-30

316

Summary of Contents for VIPA System SLIO





























































































































































































































































































































































































Search results

Summary of Contents for VIPA System SLIO

Reviews:

Brands by name

Popular brands

YASKAWA VIPA System SLIO, Manual

Search results

Summary of Contents for VIPA System SLIO

Reviews:

Brands by name

Popular brands