manualshive.com logo in svg

YASKAWA VIPA System SLIO, Manual

Share
Download
YASKAWA VIPA System SLIO Manual Download Page 157

Error

LED

 red

Description

1F

Error power supply sensor

no error

2F

Error at overload respectively short circuit at the outputs

no error

5.9  Pulse train

5.9.1  Properties

n

By presetting of time parameters, the CPU evaluates a pulse sequence with

according pulse/pause ratio and outputs it via the according output channel.

n

The output is a pulse-direction command (P/D).
–

Output frequency pattern via pulse train channel

–

To output the direction, an additional output is to be used, which is to be con-

trolled via your user program.

n

Channel 0 and 1 are supported

n

Control by the user program via SFB 49

More information about the usage of this block may be found in the

manual "SPEED7 Operation List" from VIPA.

1

Number of pulses

2

Period duration

3

Pulse duration

4

Pulse pause

The counting function is disabled during the pulse train output on the

same channel.

VIPA System SLIO

Deployment I/O periphery

Pulse train > Properties

HB300 | CPU | 013-CCF0R00 | en | 19-30

 

157

Summary of Contents for VIPA System SLIO





























































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands