manualshive.com logo in svg

YASKAWA VIPA System SLIO, Manual

Share
Download
YASKAWA VIPA System SLIO Manual Download Page 308

n

Interface networked with
–

Here you can connect the PROFINET interface to the desired subnet.

n

IP protocol
–

Here you can specify the IP address, subnet mask and gateway for the

PROFINET interface.

n

PROFINET
–

Here you can specify a 

‘PROFINET device name’

. On the Ethernet subnet, the

‘PROFINET device name’

 must be unique. For an integrated PROFINET inter-

face the 

‘PROFINET device name’

 is derived from the short description. You can

change this at any time.

n

Operating mode
–

You should not change anything here, as the settings for using the PROFINET IO

controller as an I-Device are not relevant.

PROFINET interface - Advanced options

n

Support device replacement without exchangeable medium
–

This parameter is not evaluated. With configured topology the 

device replacement

without exchangeable medium

 is supported.

PROFINET interface - Advanced options Port ...1

n

Name
–

Here you can change the name of the port, which is also shown in the configura-

tion table.

n

Comment
–

Here you can describe the port in more detail. The comment also appears in the

configuration table.

These parameters serve for the port setting of the topology.

These parameters serve for the port setting. Here the following parameters are sup-

ported:

n

Connection
–

Here you can make settings for transmission medium and type. Ensure that the

setting for the local port and the partner port are identical.

–

PROFINET requires 100Mbps in duplex mode.

n

Boundaries
–

Boundaries

 are limitations for the transfer of certain Ethernet frames. The fol-

lowing 

Boundaries

 are supported:

‘End of detection of accessible nodes’

: DCP frames for detecting accessible

nodes are not forwarded. When enabled, participants which are lying behind this

port, are no longer recognized and can not be reached by the controller.

‘End of topology discovery’

: When activated, this port does not support topology

detection, i.e. the LLDP telegrams are not forwarded.

Ethernet address

Operating mode

Interface Options

General

Port interconnection

Port options

VIPA System SLIO

Configuration with TIA Portal

TIA Portal - Deployment PG/OP communication - PROFINET > Deployment as PROFINET IO controller

HB300 | CPU | 013-CCF0R00 | en | 19-30

 

308

Summary of Contents for VIPA System SLIO





























































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands