YASKAWA VIPA System SLIO Manual Download Page 158

Page: 158 / 380

5.9.2 Wiring

5.9.2.1

Pulse train outputs

Function

Type

Description

Sys DC 24V

1L+ DC 24V for electronic section supply

Sys 0V

1M: GND for electronic section supply

DO 0.0

Pulse train 0

DO 0.1

Pulse train 1

DC 24V

2L+ 24V DC power section supply for pulse train

2M: GND for pulse train

DC 24V

3L+: DC 24V SLIO bus power section supply

3M: GND SLIO bus power section supply

5.9.3 Proceeding

PWM

and

pulse train

output use the same hardware configuration. Switching between

these modes is done within SFB 49. In the Siemens SIMATIC Manager the following

steps should be executed:

Perform a hardware configuration for the CPU.

Chap. 4.5 ‘Hardware configura-

tion - CPU’ page 69

Double-click the counter sub module of the CPU 314C-2 PN/DP.

The dialog

‘Properties’

is opened.

As soon as you select the operating mode for the corresponding channel, a dialog

box with default values for this counter mode is created and shown. For

PWM

respectively

pulse train

output select for the corresponding channel the operating

mode

‘Pulse width modulation - PWM’

Perform the required parameter settings.

Safe your project with

‘Station

Safe and compile’

Transfer your project to your CPU.

X5: Connector

Hardware configuration

VIPA System SLIO

Deployment I/O periphery

Pulse train > Proceeding

HB300 | CPU | 013-CCF0R00 | en | 19-30

158

Summary of Contents for VIPA System SLIO





























































































































































































































































































































































































Search results

Summary of Contents for VIPA System SLIO

Reviews:

Brands by name

Popular brands

YASKAWA VIPA System SLIO, Manual

Search results

Summary of Contents for VIPA System SLIO

Reviews:

Brands by name

Popular brands