YASKAWA VIPA System SLIO Manual Download Page 98

Page: 98 / 380

Here the start conditions for the

OPC UA

server are listed:

Conflicting projects
–

Simultaneous use of an

OPC UA

and

WebVisu

project via the same interface is

not permitted and results in the message

‘conflicting project on card’

–

The status

‘no conflicting project on card’

indicates that there is no conflict with a

WebVisu

project on the same interface.

Feature Set activated
–

yes: The

OPC UA

functionality is activated.

–

no: The

OPC UA

functionality is not activated.

–

Chap. 7.3 ‘Activate OPC UA functionality’ page 192

Allowed by User
–

yes: The

OPC UA

server is activated and access to it is allowed. As soon as an

OPC UA

project is found on the memory card, it is automatically started and ena-

bled for access.

–

no: You can disable and stop the

OPC UA

server by means of the CMD - auto

command

‘OPCUA_PGOP_DISABLE’

. With

‘OPCUA_PGOP_ENABLE’

you can

enable to restart the

OPC UA

server.

–

Chap. 4.18 ‘CMD - auto commands’ page 114

Allowed by Access Ways
–

yes: By default, the

OPC UA

protocol is enabled.

–

no: The

OPC UA

protocol is disabled. You can deactivate or activate the

OPC UA

protocol by means of the parameter

‘OPC UA’

in the

‘Access settings’

Hardware configured
–

yes: A hardware configuration as a precondition for the

OPC UA

communication

is loaded. The hardware configuration is checked for validity elsewhere.

–

no: A hardware configuration is not loaded e.g. after an overall reset.

–

Chap. 4.5 ‘Hardware configuration - CPU’ page 69

OPC UA project
–

loaded: An

OPC UA

OPC UA project is loaded.

–

not loaded: An

OPC UA

OPC UA project is not loaded.

–

Chap. 7 ‘Deployment OPC UA’ page 183

State
–

Running: The start conditions are fulfilled and the

OPC UA

server is started.

–

Stopped: The

OPC UA

server is stopped.

–

Startup failure: The

OPC UA

server can not be started.

–

Starting: The

OPC UA

server currently starts up.

–

Stopping: The

OPC UA

server currently stopps.

Endpoint URL
–

As soon as the

OPC UA

server is started, the endpoint URL of the

OPC UA

server is listed here.

4.11.1.1.2

Tab: ‘WebVisu’

Information about the web visualization (

‘WebVisu’

) are shown here. The creation of a

‘WebVisu’

project is only possible with the

SPEED7 Studio

V1.7.0 and up.

Chap. 8

‘Deployment WebVisu - Web visualization’ page 209

Start Conditions

Server

VIPA System SLIO

Deployment CPU 013-CCF0R00

Accessing the web server > Device web page CPU

HB300 | CPU | 013-CCF0R00 | en | 19-30

Summary of Contents for VIPA System SLIO





























































































































































































































































































































































































Search results

Summary of Contents for VIPA System SLIO

Reviews:

Brands by name

Popular brands

YASKAWA VIPA System SLIO, Manual

Search results

Summary of Contents for VIPA System SLIO

Reviews:

Brands by name

Popular brands