manualshive.com logo in svg

YASKAWA VIPA System SLIO, Manual

Share
Download
YASKAWA VIPA System SLIO Manual Download Page 299

For parametrization click at the CPU at slot 0 in the 

Device overview

 of the PROFINET IO

device 

‘VIPA SLIO System’

. Then the parameters of the CPU part are shown in the 

Prop-

erties dialog

. Here you can make your parameter settings. 

Ä

 Chap. 4.9 ‘Setting VIPA

specific CPU parameters’ page 82

13.4  TIA Portal - Hardware configuration - Ethernet PG/OP channel

Please note!

–

At the first commissioning respectively after a reset to factory setting

the Ethernet interface has no IP address.

–

For online access, you have to assign valid IP address data to it by

means of "Initialization".

–

After initialization, you can transfer the IP address data to your

project.

The CPU has an integrated Ethernet PG/OP channel. This channel allows you to pro-

gram and remote control your CPU.

n

The Ethernet PG/OP channel (X1/X2) is designed as switch. This enables PG/OP

communication via the connections X1 and X2.

n

Configurable connections are possible.

n

DHCP respectively the assignment of the network configuration with a DHCP server

is supported.

n

Default diagnostics addresses: 2025 ... 2040

n

Via the Ethernet PG/OP channel, you have access to:
–

Device website, where you can find information on firmware status, connected

peripherals, current cycle times, etc.

–

OPC UA

 project, which is to be created in the 

OPC UA Configurator

.

–

WebVisu

 project, which is to be created in the 

SPEED7 Studio

.

–

PROFINET IO controller or the PROFINET I-Device.

1.

Install your System SLIO with your CPU.

2.

Wire the system by connecting cables for voltage supply and signals.

3.

Connect the one of the Ethernet jacks (X1, X2) of the Ethernet PG/OP channel to

Ethernet.

4.

Switch on the power supply.

ð

After a short boot time the CP is ready for communication. He possibly has no

IP address data and requires an initialization.

Setting VIPA specific CPU

parameters

Overview

Assembly and commis-

sioning

VIPA System SLIO

Configuration with TIA Portal

TIA Portal - Hardware configuration - Ethernet PG/OP channel 

HB300 | CPU | 013-CCF0R00 | en | 19-30

 

299

Summary of Contents for VIPA System SLIO





























































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands