manualshive.com logo in svg

YASKAWA VIPA System SLIO, Manual

Share
Download
YASKAWA VIPA System SLIO Manual Download Page 309

n

Start address
–

The CPU reports errors of the IO controller via the 

‘Start address’

, as soon as

e.g. an error during synchronization of the IO controller occurs. This address is

also used to identify the IO system to which the device belongs, if an IO device

fails.

13.6.1.4 

Configuration PROFINET IO device

n

The modules, which may be configured here are listed in the hardware catalog.

n

For the deployment of the PROFINET IO devices from VIPA you have to include the

modules into the hardware catalog by means of the GSDML file from VIPA.

n

After the installation of the GSDML file the PROFINET IO devices from VIPA may be

found in the hardware catalog at 

Additional field devices > PROFINET > IO > VIPA

GmbH > VIPA SLIO System

Thus, the VIPA components can be shown, you have to deactivate the

"Filter" of the hardware catalog.

Diagnostic addresses

Precondition

VIPA System SLIO

Configuration with TIA Portal

TIA Portal - Deployment PG/OP communication - PROFINET > Deployment as PROFINET IO controller

HB300 | CPU | 013-CCF0R00 | en | 19-30

 

309

Summary of Contents for VIPA System SLIO





























































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands