manualshive.com logo in svg

Xerox DocuColor 2240, Service Manual


Share
Download
background image

09/03
2-617

DC 3535/2240/1632, WC M24

102-372, 102-373

Status Indicator RAPs

Initial issue 

102-372 Interface Sequence

Interface sequence failure. The initial command from the Controller was not notified within a
specified time.

Initial Actions

•

Switch power off then on.

•

Remove and reseat the NVM PWBs, PS-1 and PS-2 ROM PWBs, the RAM PWBs, and
the ESS PWB. Make sure that all of the PWBs on the ESS PWBs are in the correct slot.

•

Perform all of 

GP 3

.

Procedure

Switch off the power. Remove the HDD (

PL 13.1

). Switch on the power. 

Fault code 102-372

is still declared
Y

N

If a HDD fault (usually 116-201) is declared, replace the HDD (

PL 13.1

).

Reinstall the HDD.  

There is +3.3 VDC from P/J300 pin on the ESS PWB to GND.

Y

N

Go to the 3.3VDC wirenet, 

Figure 1

 (2240/1632), or 

Figure 2

 (3535) and check for +3.3

VDC between 

 P/J510

 on LVPS 1 and P/J300 on the ESS PWB. Repair or replace as

required. Refer to the 

OF 1-1

 RAP.

CAUTION

GP10 is used to maintain the integrity of the serial number and billing data when one or more
serialized PWBs must be replaced. Never replace all three listed PWBs at the same time. If
any of the PWBs needs replacing, only replace them one at a time.

•

ESS NVM PWB (

PL 13.1

). 

•

MCU NVM PWB (

PL 13.1

). 

•

ESS PWB (

PL 13.1

). 

Failure to comply with 

GP 10

 could result in catastrophic NVM corruption.

Check the cable (

PL 18.3

) from 

 P/J344

 on the ESS PWB to 

 P/J727

 on the IIT/IPS PWB. If the

wires are OK, replace the ESS NVM PWB (

PL 13.1

). If the problem persists, reinstall the origi-

nal NVM PWB, then replace the PS-1 and/or PS-2 ROMs (

PL 13.1

). If the problem remains,

replace the ESS PWB (

PL 13.1

). 

102-373 Channel

Channel failure. The channel notified from the Controller was incorrect.

Procedure

Switch power off then on. 

The problem continues.

Y

N

Return to service call procedures.

Perform re-installation of the software.

Summary of Contents for DocuColor 2240


















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for DocuColor 2240

Magtek ExpressCard 2000 Preventive Maintenance Procedure preview
ExpressCard 2000
Brand: Magtek Pages: 25
TallyGenicom 6600 Series Quick Reference Manual preview
6600 Series
Brand: TallyGenicom Pages: 310
TallyGenicom 6600 Series Applications Manual preview
6600 Series
Brand: TallyGenicom Pages: 330
Xerox 4250 - WorkCentre - Copier System Administration Manual preview
4250 - WorkCentre - Copier
Brand: Xerox Pages: 210
Xerox 4150 - WorkCentre B/W Laser Competitive Comparison preview
4150 - WorkCentre B/W Laser
Brand: Xerox Pages: 4
Xerox 4118P - WorkCentre B/W Laser Evaluator Manual preview
4118P - WorkCentre B/W Laser
Brand: Xerox Pages: 16
Xerox 3635MFP - Phaser B/W Laser Voluntary Product Accessibility Template preview
3635MFP - Phaser B/W Laser
Brand: Xerox Pages: 10
Xerox 3635MFP - Phaser B/W Laser Quick Use Manual preview
3635MFP - Phaser B/W Laser
Brand: Xerox Pages: 42
Xerox 3300MFP - Phaser B/W Laser User Manual preview
3300MFP - Phaser B/W Laser
Brand: Xerox Pages: 148
Xerox 3250D - Phaser B/W Laser Printer Evaluator Manual preview
3250D - Phaser B/W Laser Printer
Brand: Xerox Pages: 12
Xerox 4595 Introducing preview
4595
Brand: Xerox Pages: 4
Xerox 700i Product Information preview
700i
Brand: Xerox Pages: 12
Xerox 700i Information Card preview
700i
Brand: Xerox Pages: 12
Xerox 4250 - WorkCentre - Copier Evaluator Manual preview
4250 - WorkCentre - Copier
Brand: Xerox Pages: 16
Xerox Phaser 6140N Compatibility Manual preview
Phaser 6140N
Brand: Xerox Pages: 3
Xerox DocuColor 240 Booklet Creation For Copy preview
DocuColor 240
Brand: Xerox Pages: 2
NEC Pinwriter P6 Specification preview
Pinwriter P6
Brand: NEC Pages: 10
Xerox WorkCentre 7655 Evaluator Manual preview
WorkCentre 7655
Brand: Xerox Pages: 24

Brands by name

Popular brands

Load more brands