Xerox DocuColor 2240 Service Manual Download Page 946

Page: 946 / 1489

09/03
4-163

DC 3535/2240/1632, WC M24

ADJ 6.1

Repairs and Adjustments

Initial issue

Check that Alignment Tool can be installed through frame into alignment hole in Full Rate
Carriage (

Figure 5

If Alignment Tool fits through frame hole into Full Rate Carriage Alignment Hole, perform
the same check at the rear of the carriage.

If the rear of the carriage is aligned, the check is good.

If the rear of the carriage is not aligned, go to the adjustment.

If Alignment Tool does not fit through frame hole into Full Rate Carriage Alignment Hole,
go to the adjustment.

Figure 5 Checking Alignment Tool in Full Rate Carriage

Adjustment

NOTE: Front of Full Rate Carriage shown. Adjustment steps are same for rear of Full Rate
Carriage.

Adjust Full Rate Carriage (

Figure 6

Loosen Screw.

Move carriage so that Alignment Tool will drop into Alignment Holes.

Tighten Screw.

Figure 6 Adjust Full Rate Carriage

Screw

Alignment
Holes

Summary of Contents for DocuColor 2240


















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for DocuColor 2240

Reviews:

Related manuals for DocuColor 2240

Brands by name

Popular brands

Xerox DocuColor 2240, Service Manual

Search results

Summary of Contents for DocuColor 2240

Reviews:

Related manuals for DocuColor 2240

Brands by name

Popular brands