manualshive.com logo in svg

Xerox DocuColor 2240, Service Manual


Share
Download
background image

09/03
6-114

DC 3535/2240/1632, WC M24

dC351, dC355

Initial issue

General Procedures and Information

•

Chain 746 

•

Chains 751 -753

•

Chain  760

•

Chain  762

•

Chain  764

•

Chain  769

b.

If 

IIT

 is selected Machine Settings in NVM Chains 710 and 715 will be restored.

c.

If 

IOT

 is selected, Machine Settings in the following NVM chains will be restored:

•

Chains 700 -701

•

Chain 720 

•

Chain  730

•

Chain 770 

•

Chain  780

•

Chain  785

•

Chain  790

•

Chains 801 - 803

•

Chain 810 

•

Chain 820 

•

Chain 823 

•

Chain  830

•

Chain 840 

•

Chain 850 

•

Chain  860

Special Batch Write

This routine is intended primarily for initial setup prior to shipment to a customer location, but it
can be used to restore machine setting to their as-delivered state. This may be necessary if the
NVM was initialized without saving machine settings, or in the case of a 103-208 fault code

1.

Select the market region for the installation.

2.

Press the 

Batch Write NVM

 button.

Save/Restore NVM

1.

Press the 

Background Read

 button. This will read all locations in the dC 131 database.

This will require approximately 20 minutes to complete.

CAUTION

The NVM data is saved in RAM only. If the PWS Tools program is closed or if the PWS is
switched off, the data will be lost.

2.

Press the 

Save Current NVM Settings

 button. This will store the NVM data is the PWS

memory.

CAUTION

If the PWS is disconnected from the machine during NVM Restore, ALL NVM data may be lost

3.

To load the saved data into the machine NVM, press the 

Restore Saved NVM Settings

button. This will require approximately 20 minutes to complete, and must not be inter-
rupted.

dC355 Hard Disk Diagnostic Program

Purpose

NOTE: For details on dC355 Hard Disk Diagnostic Program, see Adjustments: 

ADJ 9.8

. 

Summary of Contents for DocuColor 2240


















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for DocuColor 2240

Panasonic KX-P8415 Setup And Reference Manual preview
KX-P8415
Brand: Panasonic Pages: 32
Samsung SPP 2020 - Photo Printer - 20 Sheets Manual Del Usuario preview
SPP 2020 - Photo Printer - 20 Sheets
Brand: Samsung Pages: 81
Samsung ML-6000 Bedienungsanleitung preview
ML-6000
Brand: Samsung Pages: 98
Samsung ML-4050N Compatibility Manual preview
ML-4050N
Brand: Samsung Pages: 6
Samsung ML-3750ND User Manual preview
ML-3750ND
Brand: Samsung Pages: 203
Samsung ML-3312ND Manual Del Usuario preview
ML-3312ND
Brand: Samsung Pages: 264
Samsung ML-2165W/XAA Manual Del Usuario preview
ML-2165W/XAA
Brand: Samsung Pages: 228
Samsung ML-2165 User Manual preview
ML-2165
Brand: Samsung Pages: 211
Samsung ML-2525 Brochure & Specs preview
ML-2525
Brand: Samsung Pages: 5
Samsung ML-1865W Manual Del Usuario preview
ML-1865W
Brand: Samsung Pages: 92
Samsung ML-1865W User Manual preview
ML-1865W
Brand: Samsung Pages: 75
Samsung ML-6060 Technical Instructions preview
ML-6060
Brand: Samsung Pages: 11
Samsung ML-1450 Series Manual Del Usuario preview
ML-1450 Series
Brand: Samsung Pages: 206
Samsung ML 3050 - B/W Laser Printer Manual Del Usuario preview
ML 3050 - B/W Laser Printer
Brand: Samsung Pages: 103
Samsung ML 3050 - B/W Laser Printer User Manual preview
ML 3050 - B/W Laser Printer
Brand: Samsung Pages: 215
Samsung ML-1450 Series Quick Manual preview
ML-1450 Series
Brand: Samsung Pages: 2
Samsung CLP 510N - Color Laser Printer User Manual preview
CLP 510N - Color Laser Printer
Brand: Samsung Pages: 266
Samsung 550N - CLP Color Laser Printer Manual De Instalación preview
550N - CLP Color Laser Printer
Brand: Samsung Pages: 296

Brands by name

Popular brands

Load more brands