manualshive.com logo in svg

Xerox DocuColor 2240, Service Manual


Share
Download
background image

09/03

4-43

DC 3535/2240/1632, WC M24

REP 6.3, REP 6.4

Repairs and Adjustments

Initial issue 

REP 6.3 IIT Top Cover

Removal

WARNING

To avoid personal injury or shock, do not perform repair or adjustment activities with
the power switch on or electrical power applied to the machine.

1.

Remove DADF (

REP 5.1

). 

2.

Remove Screws (2) from the top front of IIT Top Cover.

3.

Loosen Screws (2) under Control Panel (one each end towards the machine rear).

4.

Remove the Screw from the rear of the IIT Top Cover, left side.

5.

Remove the Document Output Tray.

6.

Remove the Document Output Tray support bracket Screws (4) and Brackets (2).

7.

Lift the IIT Top Cover to access harness connectors (2). Disconnect P/J’s and remove IIT
Top Cover.

REP 6.4 Lens Kit

Parts List on 

PL 18.4

Removal

WARNING

To avoid personal injury or shock, do not perform repair or adjustment activities with
the power switch on or electrical power applied to the machine.

1.

Remove Platen Glass (

REP 6.2

).

CAUTION

In the following, do not remove any screws with red markings.

2.

Remove the Lens/CCD Chassis (

Figure 1

). 

Figure 1 Removing Lens Cover

Replacement

1.

Align APS Sensor with marks made during the removal procedure before tightening the
mounting screw.

2.

Adjust the IIT Calibration (

ADJ 9.7

). 

2

Remove the screw (1) 
and APS Sensor 
bracket

1

Mark the 
position of 
the APS 
Sensor 
bracket

3

Remove Lens 
Cover screws (6) 
and Lens Cover

4

Disconnect CCD Connector 
(not shown) and remove 
Lens/CCD Chassis screws 
(4) (2 each side)

5

Remove the Lens/CCD 
Chassis

Summary of Contents for DocuColor 2240


















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for DocuColor 2240

Magicard Pronto Getting Started Manual preview
Pronto
Brand: Magicard Pages: 26
QMS 3260 Operation preview
3260
Brand: QMS Pages: 194
Samsung SCX-4720F Manual Del Usuario preview
SCX-4720F
Brand: Samsung Pages: 322
Samsung SCX-3405FW User Manual preview
SCX-3405FW
Brand: Samsung Pages: 340
Samsung SCX-6320F Manual Del Usuario preview
SCX-6320F
Brand: Samsung Pages: 349
Samsung SCX-6220 User Manual preview
SCX-6220
Brand: Samsung Pages: 330
Samsung Xpress M2070FW User Manual preview
Xpress M2070FW
Brand: Samsung Pages: 315
Samsung SL-M2870FW Quick Installation Manual preview
SL-M2870FW
Brand: Samsung Pages: 2
Samsung SL-M2625D Installation Manual preview
SL-M2625D
Brand: Samsung Pages: 2
Samsung SL-M2625D User Manual preview
SL-M2625D
Brand: Samsung Pages: 232
Samsung SF-5800P User Manual preview
SF-5800P
Brand: Samsung Pages: 42
Samsung SCX-6545N Series User Manual preview
SCX-6545N Series
Brand: Samsung Pages: 468
Samsung SF-565PR User Manual preview
SF-565PR
Brand: Samsung Pages: 196
Samsung SCX4521F - B/W Laser - All-in-One User Manual preview
SCX4521F - B/W Laser - All-in-One
Brand: Samsung Pages: 120
Eaton Power Defense PD3 Mounting And Operating Instructions preview
Power Defense PD3
Brand: Eaton Pages: 4
idp SMART-30R User Manual preview
SMART-30R
Brand: idp Pages: 88
Xerox 4150S - WorkCentre B/W Laser Brochure & Specs preview
4150S - WorkCentre B/W Laser
Brand: Xerox Pages: 4
Canon PIXMA MG3120 Getting Started Manual preview
PIXMA MG3120
Brand: Canon Pages: 4

Brands by name

Popular brands

Load more brands