manualshive.com logo in svg

Xerox DocuColor 2240, Service Manual


Share
Download
background image

09/03
2-235

DC 3535/2240/1632, WC M24

10-398

Status Indicator RAPs

Initial issue 

10-398 Fan Lock

The machine logic detected a failure of the Fuser Fan, LVPS Fan or the Rear Fan.

Procedure

Enter 

dC330

 [004-050]. Press 

Start

. 

 The Fuser Fan (

PL 8.1

) revolves at high speed.

Y

N
There is +24 VDC from 

 P/J222

 pin 1 to pin 4. 

Y

N
There is +24 VDC from 

 P/J407

 pin A14 to pin A17.

Y

N

Replace the MCU PWB (

PL 13.1

)

Refer to 

Figure 1

. Check the wires from J407 pins A14 and A17 to the Fuser Fan for

an open circuit.

There is +24 VDC from 

 P/J407

 pin A15 to pin A14.

Y

N

Replace the MCU PWB (

PL 13.1

)

Press 

Stop

. 

There is +24 VDC from 

 P/J407

 pin A15 to pin A17. 

Y

N

Refer to 

Figure 1

. Check for an open circuit (greater than 30K ohms) from J407- A14

to J407-A15 (through the Fuser Fan). If the wires are OK, replace the Fuser Fan (

PL

8.1

).

 Replace the Fuser Fan (

PL 8.1

). If the problem continues, replace the MCU PWB (

PL

13.1

). 

The Rear Fan (

PL 8.1

) revolves at high speed.

Y

N
There is +24 VDC from 

 P/J552

 pin 1 to pin 4. 

Y

N

Refer to 

Figure 2

 (DC 2240/1632) or 

Figure 3

 (DC 3535) Check the wires and con-

nectors for a short circuit. If the check is OK, replace the MCU PWB (

PL 13.1

). If the

problem continues replace the I/F PWB (

PL 9.1

).

There is +24 VDC from 

 P/J552

 pin 1 to pin 2. 

Y

N

Replace the MCU PWB (

PL 13.1

). 

Press 

Stop

. 

There is +24 VDC from 

 P/J552

 pin 2 to pin 4. 

Y

N

Refer to 

Figure 2

 (DC 2240/1632) or 

Figure 3

 (DC 3535) Check for an open circuit

(greater than 30K ohms) from J552-1 to J552-2 (through the Rear Fan). If the wires
are OK, replace the Rear Fan (

PL 8.1

).

Replace the Rear Fan (

PL 8.1

). If the problem continues, replace the MCU PWB (

PL

13.1

).

The LVPS Fan revolves at high speed (

PL 9.1

). 

Y

N
The machine is a DC 3535. 
Y

N
There is +24 VDC from 

 P/J214

 pin 1 to pin 4. 

Y

N
There is +24 VDC from 

 P/J406

 pin B11 to pin B14.

Y

N

Replace the MCU PWB (

PL 13.1

)

Refer to 

Figure 4

. Check the wires from J406 pins B11 and B14 to the LVPS

Fan for an open circuit.

There is +24 VDC from 

 P/J406

 pin B12 to pin B11.

Y

N

Replace the MCU PWB (

PL 13.1

)

Press 

Stop

. 

There is +24 VDC from 

 P/J406

 pin B12 to pin B14. 

Y

N

Refer to 

Figure 4

. Check for an open circuit (greater than 30K ohms) from

J406- B12 to J406-B14 (through the LVPS Fan). If the wires are OK, replace
the LVPS Fan (

PL 9.1

).

 Replace the LVPS Fan (

PL 9.1

). If the problem continues, replace the MCU PWB

(

PL 13.1

). 

There is +24 VDC from 

 P/J214

 pin 1 to pin 4. 

Y

N
There is +24 VDC from 

 P/J406

 pin B10 to pin B13.

Y

N

Replace the MCU PWB (

PL 13.1

)

Refer to 

Figure 5

. Check the wires from J406 pins B10 and B13 to the LVPS Fan for

an open circuit.

There is +24 VDC from 

 P/J406

 pin B11 to pin B10.

Y

N

Replace the MCU PWB (

PL 13.1

)

Press 

Stop

. 

There is +24 VDC from 

 P/J406

 pin B11 to pin B13. 

Y

N

Refer to 

Figure 5

. Check for an open circuit (greater than 30K ohms) from J406- B11

to J406-B13 (through the LVPS Fan). If the wires are OK, replace the LVPS Fan (

PL

9.1

).

 Replace the LVPS Fan (

PL 9.1

). If the problem continues, replace the MCU PWB (

PL

13.1

). 

With 

dC330

 [004-050] entered, stack 

dC330

 [004-200] and press 

Start

. 

The display is L. 

Y

N

Check the wires and connectors. If the check is OK, replace the MCU PWB (

PL 13.1

). 

The Fans are operating correctly. If the problem continues replace the MCU PWB (

PL 13.1

).

Summary of Contents for DocuColor 2240


















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for DocuColor 2240

Panasonic Workio DP-C265 Operating Instructions Manual preview
Workio DP-C265
Brand: Panasonic Pages: 102
Panasonic DP-CL21 Series Operating Instructions Manual preview
DP-CL21 Series
Brand: Panasonic Pages: 9
Panasonic DP-CL21 Series Specifications preview
DP-CL21 Series
Brand: Panasonic Pages: 2
TASKalfa 306ci First Steps preview
306ci
Brand: TASKalfa Pages: 36
IBM 5218 Setup Procedures preview
5218
Brand: IBM Pages: 60
Canon imageRUNNER ADVANCE DX 6870i Service Manual preview
imageRUNNER ADVANCE DX 6870i
Brand: Canon Pages: 115
Canon imagerunner advance C5550i User Manual preview
imagerunner advance C5550i
Brand: Canon Pages: 1556
Oki LP470s Manual Rapide preview
LP470s
Brand: Oki Pages: 140
TEC B-470-QQ Series Owner'S Manual preview
B-470-QQ Series
Brand: TEC Pages: 32
SainSmart Genmitsu 3018-MX3 User Manual preview
Genmitsu 3018-MX3
Brand: SainSmart Pages: 50
Brady BradyPrinter A5500 User Manual preview
BradyPrinter A5500
Brand: Brady Pages: 72
Star Micronics NX-1001 User Manual preview
NX-1001
Brand: Star Micronics Pages: 130
Star Micronics SP200 Series User Manual preview
SP200 Series
Brand: Star Micronics Pages: 127
Seiko Epson P130A Manual preview
P130A
Brand: Seiko Epson Pages: 301
Oce CS655 User Manual preview
CS655
Brand: Oce Pages: 495
Canon MultiPASS C530 Quick Start Manual preview
MultiPASS C530
Brand: Canon Pages: 8
Canon MultiPASS F30 Reference Manual preview
MultiPASS F30
Brand: Canon Pages: 58
Canon MultiPASS F20 Basic Manual preview
MultiPASS F20
Brand: Canon Pages: 110

Brands by name

Popular brands

Load more brands