manualshive.com logo in svg

Xerox DocuColor 2240, Service Manual


Share
Download
background image

09/03

6-9

DC 3535/2240/1632, WC M24

dC131

General Procedures and Information

Initial issue 

dC131 NVM Read/Write

Purpose

Reads, sets or changes the NVM data.

Procedure

Module Selection

1.

Enter the 

Diagnostic Mode

. Refer to 

Entering Diagnostic Mode using the PWS

.

2.

Select 

Adjustments

 in the Service Entry Screen.

3.

The system displays one of the Read/Write Screens. dC131 NVM Read/Write is the
default screen.

4.

Select a 

Sub-System

 from the Vertical Left Tab List. The default tab is 

All

.

Reading NVM

1.

Select an 

ID

 from the Sub-System Table, then click 

Read NVM

, or double click on the line

ID 

and the value will be read in the 

Value

 column. 

The 

Range Check

 column will fill in.

Writing NVM

1.

To change a value, enter a new value in the 

New

 column and press 

Enter

.

2.

When a new value is entered, the 

Changed

 tab will turn green. The number in parenthe-

ses count the number of pending NVM values. Clicking this tab will show a list of all the
changed values. These locations can be written individually or as a block from this tab, or
can be canceled.

3.

Select 

Write NVM

.

a.

If the input value is valid (within the range), the system writes the new NVM value in
the NVM location in the machine.

b.

If the input value is invalid, the system displays the following message in the infor-
mation screen, The

 given NVM value is out of range. NVM was not changed

.

c.

If the NVM cannot be changed (Write protected NVM), the system displays the fol-
lowing message, 

The specified NVM is read only

.

4.

When the system writes the new value in the specified NVM code, the value is updated in
the 

New

 box and reduces the count in the Changed Tab.

Table 1 Module Selection

Module item

Chain number allocation

All

700 - 999

UI/Tools

700, 720

IISS

715

Config/System 719, 

740

Xfer

746

RegiCon

760

PHM

742

DADF

710

Xero

751

Drives / Output

741, 764

ProCon 752

Developer

762

Fuser

744

Other

755, 769

Errors (number of errors)

Displays and NVM outside of the ranges listed in the 
PWS database.

Changed (number pending change)

Displays any with new value entered in the New col-
umn, but not written yet.

Summary of Contents for DocuColor 2240


















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for DocuColor 2240

idp SMART-30R User Manual preview
SMART-30R
Brand: idp Pages: 88
Oki OKIPAGE 8z Technical Features preview
OKIPAGE 8z
Brand: Oki Pages: 2
Oki OKIPAGE 8c Plus User Manual preview
OKIPAGE 8c Plus
Brand: Oki Pages: 48
Oki OKIPAGE 6e Maintenance Manual preview
OKIPAGE 6e
Brand: Oki Pages: 257
Oki OKIPAGE 14i Technical Reference preview
OKIPAGE 14i
Brand: Oki Pages: 113
Oki OKIPAGE 14e Setup Manual preview
OKIPAGE 14e
Brand: Oki Pages: 26
Oki OKIPAGE 14e Service Manual preview
OKIPAGE 14e
Brand: Oki Pages: 183
Oki MPS730b Material Safety Data Sheet preview
MPS730b
Brand: Oki Pages: 36
Oki MPS730b User Manual preview
MPS730b
Brand: Oki Pages: 136
Oki MPS710c Handy Reference preview
MPS710c
Brand: Oki Pages: 66
Oki MPS711c Manual De L'Utilisateur preview
MPS711c
Brand: Oki Pages: 123
Oki MPS711c User Manual preview
MPS711c
Brand: Oki Pages: 109
Oki Microline 520 User Manual preview
Microline 520
Brand: Oki Pages: 68
Oki Microline 3320 Maintenance Manual preview
Microline 3320
Brand: Oki Pages: 12
Oki OKIPOS X400 Manual De L'Utilisateur preview
OKIPOS X400
Brand: Oki Pages: 22
Oki OKIPOS X400 Guía Del Usuario preview
OKIPOS X400
Brand: Oki Pages: 22
Oki OKIPOS X400 User Manual preview
OKIPOS X400
Brand: Oki Pages: 27
Oki OKIPAGE 12i Series Maintenance Manual preview
OKIPAGE 12i Series
Brand: Oki Pages: 210

Brands by name

Popular brands

Load more brands