manualshive.com logo in svg

Xerox DocuColor 2240, Service Manual


Share
Download
background image

09/03

2-98

DC 3535/2240/1632, WC M24

5-902, 5-903

Initial issue

Status Indicator RAPs

5-902 Power On Registration Sensor

The Registration Sensor detected a document when the Top Cover/platen Interlock was closed
or power was switched on. 

Initial Actions

Clean the Registration Sensor. Ensure there are no pieces of paper on the sensor.

This problem may be caused by running prepunched (CFF) forms through the DADF. Instruct
the operator.

Check the operator documents. Ensure they are not folded, curled, thin paper, or out of specifi-
cation for the DADF.

Procedure

Enter 

dC330

 [005-110] and select 

Start

.  

The display indicates High.

Y

N

Disconnect 

 P/J599

 from the DADF Control PWB. 

The display changes to High.

Y

N

Replace the DADF Control PWB (

PL 20.3

). 

Go to 

Flag 1

. Check the wire for a short circuit. If the wire is good, replace the Registration

Sensor (

PL 20.5

). 

The Registration Sensor appears to be functioning correctly. Check the wires from the sensor
to the DADF Control PWB. Look for loose connectors/pins. If the problem continues, replace
the Registration Sensor (

PL 20.5

). If the problem continues, replace the DADF Control PWB

(

PL 20.3

) 

Figure 1 5-902 RAP Circuit Diagram - DADF Registration Sensor 

5-903 Power On Exit Sensor

The DADF Exit Sensor detected a document when the Top Cover/platen Interlock was closed

or power was switched on. 

Initial Actions

Clean the Exit Sensor. Ensure there are no pieces of paper on the sensor.

Procedure

Enter 

dC330

 [005-115] and select 

Start

.  

The display indicates High.

Y

N

Disconnect 

 P/J599

 from the DADF Control PWB.  

The display changes to High.

Y

N

Replace the DADF Control PWB (

PL 20.3

). 

Go to 

Flag 1

. Check the wire for a short circuit. If the wire is good, replace the Exit Sensor

(

PL 20.9

). 

The Exit Sensor appears to be functioning correctly. Check the wires from the sensor to the
DADF Control PWB. Look for loose connectors/pins. If the problem continues, replace the Exit
Sensor (

PL 20.9

). If the problem continues, replace the DADF Control PWB (

PL 20.3

) 

Figure 1 5-903 RAP Circuit Diagram - Exit Sensor 

Summary of Contents for DocuColor 2240


















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for DocuColor 2240

idp SMART-30R User Manual preview
SMART-30R
Brand: idp Pages: 88
VuPoint IP-P20-VP User Manual preview
IP-P20-VP
Brand: VuPoint Pages: 20
Konica Minolta Bizhub 4050i Shortcut Manual preview
Bizhub 4050i
Brand: Konica Minolta Pages: 44
OKIDATA Microline 393 Setup Manual preview
Microline 393
Brand: OKIDATA Pages: 44
Oki ColorPainter M-64S User Manual preview
ColorPainter M-64S
Brand: Oki Pages: 84
DNP DP-DS80D Startup Manual preview
DP-DS80D
Brand: DNP Pages: 33
Arrayit NanoPrint LM210 User Manual preview
NanoPrint LM210
Brand: Arrayit Pages: 23
Oki MAC TECHNICAL REFERANCE C7350 User Manual preview
MAC TECHNICAL REFERANCE C7350
Brand: Oki Pages: 95
Savin SDC103 Operating Instructions Manual preview
SDC103
Brand: Savin Pages: 90
Brother FAX 1840C Service Manual preview
FAX 1840C
Brand: Brother Pages: 401
Gestetner G056 Service Manual preview
G056
Brand: Gestetner Pages: 335
Panasonic KX-P1131 - KX-P 1131 B/W Dot-matrix Printer Service Manual preview
KX-P1131 - KX-P 1131 B/W Dot-matrix Printer
Brand: Panasonic Pages: 6
Panasonic KX-MC6000 Series Driver Installation Manual preview
KX-MC6000 Series
Brand: Panasonic Pages: 5
Panasonic KX-MB1536CX Specifications preview
KX-MB1536CX
Brand: Panasonic Pages: 4
Panasonic KX-CL400 Brochure & Specs preview
KX-CL400
Brand: Panasonic Pages: 4
Panasonic KX-CL400 Setup Manual preview
KX-CL400
Brand: Panasonic Pages: 24
Panasonic KX-P1131 - KX-P 1131 B/W Dot-matrix Printer Operating Instructions Manual preview
KX-P1131 - KX-P 1131 B/W Dot-matrix Printer
Brand: Panasonic Pages: 44
Panasonic KX-P1121E Operating Instructions Manual preview
KX-P1121E
Brand: Panasonic Pages: 43

Brands by name

Popular brands

Load more brands