09/03
6-108
DC 3535/2240/1632, WC M24
dC330
Initial issue
General Procedures and Information
009-101
Toner_Y New
CRU Connection of color is open (The CRU in
use is present, or it is not present). Low=new,
High=old
009-102
Toner_M New
CRU Connection of color is open (The CRU in
use is present, or it is not present). Low=new,
High=old
009-103
Toner_C New
CRU Connection of color is open (The CRU in
use is present, or it is not present) Low=new,
High=old
009-104
Toner_K New
CRU Connection of color is open (The CRU in
use is present, or it is not present) Low=new,
High=old
009-150
TNR FULL SNR
ON = High
009-151
#Y_CRU detect
CRU is installed
009-152
#M_CRU detect
CRU is installed
009-153
#C_CRU detect
CRU is installed
009-154
#K_CRU detect
CRU is installed
009-200
2nd BTR Retract Sensor
Retraction. ON = Low
009-201
POB Sensor
Paper detected. ON = Low
009-203
1st BTR Retract Sensor
Retraction. ON = Low
010-101
Fuser Exit
Paper detected. ON = High
010-102
Full Paper Stack Sensor
NotFull. ON = Low
012-100
IOT Regi Clutch
Clutch OFF. ON = High
012-101
Compiler Tray Exit Sensor
Paper detected. ON = High
012-102
Compiler Paper Sensor
Paper detected. ON = High
012-103
H-Tra Ent. Sensor
Paper detected. ON = High
012-104
H-Tra Exit Sensor
Paper detected. ON = High
012-200
Stacker Paper Sensor
Paper detected. ON = High
012-201
Stacker Height Sensor
Higher than the detection surface. ON = High
012-202
Stacker Upper Limit Sensor
Upper Limit position. ON = High
012-204
Stacker Stack A Sensor
Non-transmissive position. ON = High
012-205
Stacker Stack B Sensor
Non-transmissive position. ON = High
012-207
Staple Head Home Sensor
Not at Home position. ON = High
012-208
Low Staple Switch
Low Staple. ON = High
012-209
Staple Ready Sensor
Not at Ready position. ON = High
012-210
Eject Clamp Home Sensor
Not at Home Position (Roller is down). ON = High
012-211
Set Clamp Home Sensor
Not at Home Position (transmissive). ON = High
012-212
Rear Tamper Home Sensor
Home position. ON = High
012-215
H-Tra IOT Full Paper Sensor No paper. ON = High
012-216
Front Tamper Home Sensor
Home position. ON = High
012-217
Decurler Cam Position Sen-
sor
Not at Home Position (transmissive). ON = High
Table 1 Input Component Control Codes
Code
Name
Description
012-224
Stapler Move Sensor
Non-transmissive position. ON = High
012-225
Stapler Front Corner Sensor
Front Corner position. ON = High
012-300
Front Cover Interlock Switch
Open. ON = High
012-301
Top Cover Interlock Switch
Open. ON = High
012-302
Docking Interlock Sensor
Docking release. ON = High
012-305
H-Tra Interlock Sensor
Open. ON = High
Table 2 Output Component Control Codes
Code
Name
Description
Conflicts
001-001
Delayed_off
Delay Relay
001-003
Flicker
Energize triac to switch in Flicker Resistor.
(220VAC - DC3535 only)
004-001
Steering Motor
Reswitch the Steering Cam to Home posi-
tion once and operate it at half cycle after
that.
004-005
004-002
IBT Motor (104mm/
sec.)
Operate with the IBT Assy. removed to pre-
vent Transfer Belt damage.
004-012,
004-013
004-003
Drum Motor YMC
(104mm/sec.)
Remove all Drum Cartridges before ener-
gizing to prevent Belt damage.
004-004
Main Motor
(104mm/sec.)
Rotate at medium speed. Operate the
motor with the 2nd BTR nipped, or the LH
Cover opened. Otherwise, the 2nd BTR
might damage the belt.
004-007,
004-008
004-005
Steering Motor
Home Position
Returns Steering Cam to home position
ON = Low. Operate with the IBT Assy.
removed to prevent Transfer Belt damage.
004-001
004-006
Drum Motor K
(104mm/sec.)
Remove all Drum Cartridges before ener-
gizing to prevent Belt damage.
004-004,
004-009
004-007
Main Motor (52mm/
sec.)
Rotate at low speed. Operate the motor
with the 2nd BTR nipped, or the LH Cover
opened. Otherwise, the 2nd BTR might
damage the belt.
004-004,
004-008
004-008
Main Motor (high
speed)
Rotate at high speed. Operate the motor
with the 2nd BTR nipped, or the LH Cover
opened. Otherwise, the 2nd BTR might
damage the belt.
004-004,
004-007
004-009
Drum Motor K
(52mm/sec.)
Rotate at low speed. Remove all Drum Car-
tridges before energizing to prevent Belt
damage.
004-006,
004-010
004-010
Drum Motor K (high
speed)
Rotate at high speed. Remove all Drum
Cartridges before energizing to prevent
Belt damage.
004-006,
004-009
Table 1 Input Component Control Codes
Code
Name
Description
Summary of Contents for DocuColor 2240
