manualshive.com logo in svg

Xerox DocuColor 2240, Service Manual


Share
Download
background image

09/03
4-172

DC 3535/2240/1632, WC M24

ADJ 9.9

Initial issue

Repairs and Adjustments

ADJ 9.9 IOT Registration Series (dC129)

Purpose

The purpose is to adjust the position of the printed image on the page. This is done by chang-
ing the value in the appropriate NVM location in dC129. This controls where the ROS writes
the image. 

Introduction

This series consists of 4 procedures:

Lead Edge Registration (All Trays)

Side Edge Registration (Trays 1-5)

Duplex (Side 2) Registration 

Lead Edge Registration for Tray 5

All procedures must be checked.

Lead Edge Registration (All Trays)

Purpose

To correctly set the lead edge of the image in relation to the edge of the paper. There is one
lead edge setting for Trays 1 - 5. The test pattern will print from Tray 1.

Check

1.

Connect the PWS to the machine and enter Diagnostic Mode (refer to 

Entering Diagnostic

Mode using the PWS

). Select dC129 from the 

DC Quick

 menu.

2.

Load Tray 1 with the largest paper used by the customer. Use 11x17/A3 if available.

3.

Select 

ALL

 in the 

Lead Edge

 column.

4.

Press the 

Start

 button on the screen. As the prints are made, mark each to indicate the

lead edge (flip the sheets from face down to face up without rotating).

5.

Take the third print and measure from the lead edge to point ‘A’ on 

Figure 1

 (the intersec-

tion of the 7th line from the left edge and the first line from the lead edge).

6.

If the measured value is not 21.6mm

±

0.5, perform the Adjustment.

Figure 1 Measurement points

Adjustment

1.

Use the Right and Left Arrow buttons to increase or decrease the amount of lead edge
spacing. Use the right arrow to increase the spacing (moves the grid pattern to the left).
Each click moves the image 0.25mm. The cumulative amount of shift is indicated in the

Lead Reg.

 box. 

2.

After adjusting the registration, click 

Set Adjust Value

.

NOTE: Changes made to the NVM for LE registration are not implemented unless the machine
exits Diagnostic Mode.

3.

Go to the 

Service Exit

 tab and select 

Temporary Closeout

.

4.

After the machine reboots and is ready to copy, reconnect the PWS.

5.

Repeat the check/adjustment until the specifications are met.

6.

Select 

Save [LR]

 to save the new NVM settings.

7.

Proceed to 

Side Edge Registration for Paper Trays 1 - 5

.

Summary of Contents for DocuColor 2240


















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for DocuColor 2240

Canon iP2600 - PIXMA Color Inkjet Printer Setup Instructions preview
iP2600 - PIXMA Color Inkjet Printer
Brand: Canon Pages: 2
Canon FAXPHONE L80 Setup Instructions preview
FAXPHONE L80
Brand: Canon Pages: 8
Canon ImageCLASS 2300 Network Manual preview
ImageCLASS 2300
Brand: Canon Pages: 102
Canon 1750 Service Manual preview
1750
Brand: Canon Pages: 358
Xerox 220 Getting Started preview
220
Brand: Xerox Pages: 48
Oce 3155 System Data preview
3155
Brand: Oce Pages: 4
Xerox D125 User Manual preview
D125
Brand: Xerox Pages: 310
Samsung SCX-3405FW Manual Del Usuario preview
SCX-3405FW
Brand: Samsung Pages: 347
Samsung SCX 6555N - MultiXpress Mono Multifunction Manual Del Usuario preview
SCX 6555N - MultiXpress Mono Multifunction
Brand: Samsung Pages: 180
Samsung SCX-4300 - SCX 4300 B/W Laser License Agreement preview
SCX-4300 - SCX 4300 B/W Laser
Brand: Samsung Pages: 18
Samsung SCX-4521FG - B/W Laser - All-in-One User Manual preview
SCX-4521FG - B/W Laser - All-in-One
Brand: Samsung Pages: 215
Samsung SCX 6320F - B/W Laser - All-in-One User Manual preview
SCX 6320F - B/W Laser - All-in-One
Brand: Samsung Pages: 332
Samsung SCX 4828FN - Laser Multi-Function Printer User Manual preview
SCX 4828FN - Laser Multi-Function Printer
Brand: Samsung Pages: 248
Samsung SCX 4725FN - B/W Laser - All-in-One User Manual preview
SCX 4725FN - B/W Laser - All-in-One
Brand: Samsung Pages: 253
Samsung ML 2851ND - B/W Laser Printer User Manual preview
ML 2851ND - B/W Laser Printer
Brand: Samsung Pages: 179
Samsung ML 2510 - B/W Laser Printer Manual Del Usuario preview
ML 2510 - B/W Laser Printer
Brand: Samsung Pages: 84
Samsung ML 1740 - B/W Laser Printer Manual Del Usuario preview
ML 1740 - B/W Laser Printer
Brand: Samsung Pages: 152
Samsung ML 1630 - B/W Laser Printer User Manual preview
ML 1630 - B/W Laser Printer
Brand: Samsung Pages: 142

Brands by name

Popular brands

Load more brands