Xerox DocuColor 2240 Service Manual Download Page 1177

Page: 1177 / 1489

09/03

6-86

DC 3535/2240/1632, WC M24

810-xxx ESS Copy Service Setting

Initial issue

General Procedures and Information

810-088

Color Shift - Ruddiness

0~4

0=-20 degrees; 1=-10 degrees; 2=0 degrees; 3=+10 degrees; 4=+20 degrees

810-089

Color Saturation - Ruddiness

0~4

0=Higher 2; 1=Higher 1; 2=Normal; 3=Lower 1; 4=Lower 2

810-090

Sharpness - Ruddiness

0~4

0=Sharper 2; 1=Sharper 1; 2=Normal; 3=Softer 1; 4=Softer 2

810-091

Contrast - Ruddiness

0~4

0=Stronger 2; 1=Stronger 1; 2=Normal; 3=Softer 1; 4=Softer 2

810-092

Background Suppression (Blue)

0~1

0=disable; 1=enable

810-093

Density Adjustment (Blue)

0~6

0=Lighter 3; 1=Lighter 2; 2=Lighter 1; 3=Normal; 4=Darker 1; 5=Darker 2; 6=Darker 3

810-094

Color balance (Y low density) (Blue)

0~6

0=Lighter 3; 1=Lighter 2; 2=Lighter 1; 3=Normal; 4=Darker 1; 5=Darker 2; 6=Darker 3

810-095

Color balance (Y med. density) (Blue)

0~6

0=Lighter 3; 1=Lighter 2; 2=Lighter 1; 3=Normal; 4=Darker 1; 5=Darker 2; 6=Darker 3

810-096

Color balance (Y high density) (Blue)

0~6

0=Lighter 3; 1=Lighter 2; 2=Lighter 1; 3=Normal; 4=Darker 1; 5=Darker 2; 6=Darker 3

810-097

Color balance (M low density) (Blue)

0~6

0=Lighter 3; 1=Lighter 2; 2=Lighter 1; 3=Normal; 4=Darker 1; 5=Darker 2; 6=Darker 3

810-098

Color balance (M med. density) (Blue)

0~6

0=Lighter 3; 1=Lighter 2; 2=Lighter 1; 3=Normal; 4=Darker 1; 5=Darker 2; 6=Darker 3

810-099

Color balance (M high density) (Blue)

0~6

0=Lighter 3; 1=Lighter 2; 2=Lighter 1; 3=Normal; 4=Darker 1; 5=Darker 2; 6=Darker 3

810-100

Color balance (C low density) (Blue)

0~6

0=Lighter 3; 1=Lighter 2; 2=Lighter 1; 3=Normal; 4=Darker 1; 5=Darker 2; 6=Darker 3

810-101

Color balance (C med. density) (Blue)

0~6

0=Lighter 3; 1=Lighter 2; 2=Lighter 1; 3=Normal; 4=Darker 1; 5=Darker 2; 6=Darker 3

810-102

Color balance (C high density) (Blue)

0~6

0=Lighter 3; 1=Lighter 2; 2=Lighter 1; 3=Normal; 4=Darker 1; 5=Darker 2; 6=Darker 3

810-103

Color balance (K low density) (Blue)

0~6

0=Lighter 3; 1=Lighter 2; 2=Lighter 1; 3=Normal; 4=Darker 1; 5=Darker 2; 6=Darker 3

810-104

Color balance (K med. density) (Blue)

0~6

0=Lighter 3; 1=Lighter 2; 2=Lighter 1; 3=Normal; 4=Darker 1; 5=Darker 2; 6=Darker 3

810-105

Color balance (K high density) (Blue)

0~6

0=Lighter 3; 1=Lighter 2; 2=Lighter 1; 3=Normal; 4=Darker 1; 5=Darker 2; 6=Darker 3

810-106

Color Shift (Blue)

0~4

0=-20 degrees; 1=-10 degrees; 2=0 degrees; 3=+10 degrees; 4=+20 degrees

810-107

Color Saturation (Blue)

0~4

0=Higher 2; 1=Higher 1; 2=Normal; 3=Lower 1; 4=Lower 2

810-108

Sharpness (Blue)

0~4

0=Sharper 2; 1=Sharper 1; 2=Normal; 3=Softer 1; 4=Softer 2

810-109

Contrast (Blue)

0~4

0=Stronger 2; 1=Stronger 1; 2=Normal; 3=Softer 1; 4=Softer 2

810-110

Background Suppression (Back Reflect
Guard)

0~1

0=disable; 1=enable

810-111

Density Adjustment (BRG)

0~6

0=Lighter 3; 1=Lighter 2; 2=Lighter 1; 3=Normal; 4=Darker 1; 5=Darker 2; 6=Darker 3

810-112

Color balance (Y low density) (BRG)

0~6

0=Lighter 3; 1=Lighter 2; 2=Lighter 1; 3=Normal; 4=Darker 1; 5=Darker 2; 6=Darker 3

810-113

Color balance (Y med. density) (BRG)

0~6

0=Lighter 3; 1=Lighter 2; 2=Lighter 1; 3=Normal; 4=Darker 1; 5=Darker 2; 6=Darker 3

810-114

Color balance (Y high density) (BRG)

0~6

0=Lighter 3; 1=Lighter 2; 2=Lighter 1; 3=Normal; 4=Darker 1; 5=Darker 2; 6=Darker 3

810-115

Color balance (M low density) (BRG)

0~6

0=Lighter 3; 1=Lighter 2; 2=Lighter 1; 3=Normal; 4=Darker 1; 5=Darker 2; 6=Darker 3

810-116

Color balance (M med. density) (BRG)

0~6

0=Lighter 3; 1=Lighter 2; 2=Lighter 1; 3=Normal; 4=Darker 1; 5=Darker 2; 6=Darker 3

810-117

Color balance (M high density) (BRG)

0~6

0=Lighter 3; 1=Lighter 2; 2=Lighter 1; 3=Normal; 4=Darker 1; 5=Darker 2; 6=Darker 3

810-118

Color balance (C low density) (BRG)

0~6

0=Lighter 3; 1=Lighter 2; 2=Lighter 1; 3=Normal; 4=Darker 1; 5=Darker 2; 6=Darker 3

810-119

Color balance (C med. density) (BRG)

0~6

0=Lighter 3; 1=Lighter 2; 2=Lighter 1; 3=Normal; 4=Darker 1; 5=Darker 2; 6=Darker 3

810-120

Color balance (C high density) (BRG)

0~6

0=Lighter 3; 1=Lighter 2; 2=Lighter 1; 3=Normal; 4=Darker 1; 5=Darker 2; 6=Darker 3

810-121

Color balance (K low density) (BRG)

0~6

0=Lighter 3; 1=Lighter 2; 2=Lighter 1; 3=Normal; 4=Darker 1; 5=Darker 2; 6=Darker 3

810-122

Color balance (K med. density) (BRG)

0~6

0=Lighter 3; 1=Lighter 2; 2=Lighter 1; 3=Normal; 4=Darker 1; 5=Darker 2; 6=Darker 3

810-123

Color balance (K high density) (BRG)

0~6

0=Lighter 3; 1=Lighter 2; 2=Lighter 1; 3=Normal; 4=Darker 1; 5=Darker 2; 6=Darker 3

810-124

Color Shift (BRG)

0~4

0=-20 degrees; 1=-10 degrees; 2=0 degrees; 3=+10 degrees; 4=+20 degrees

810-125

Color Saturation (BRG)

0~4

0=Higher 2; 1=Higher 1; 2=Normal; 3=Lower 1; 4=Lower 2

810-126

Sharpness (BRG)

0~4

0=Sharper 2; 1=Sharper 1; 2=Normal; 3=Softer 1; 4=Softer 2

810-127

Contrast (BRG)

0~4

0=Stronger 2; 1=Stronger 1; 2=Normal; 3=Softer 1; 4=Softer 2

Table 1 Chain 810

Chain/Link

Name

Default

Range

Description

«
...
1175
1176
1177
1178
1179
...
»

Summary of Contents for DocuColor 2240


















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for DocuColor 2240

Reviews:

Related manuals for DocuColor 2240

Brands by name

Popular brands

Xerox DocuColor 2240, Service Manual

Search results

Summary of Contents for DocuColor 2240

Reviews:

Related manuals for DocuColor 2240

Brands by name

Popular brands