WinGD X62DF Maintenance Manual Download | Manualshive

Page: 100 / 902

background image

5.1

Maintenance schedule

The maintenance intervals are given in each procedure related to the recommendations of
WinGD. The shown operating hours (or working hours) are always the total running hours of the
engine.

Data found during operation will show if it is possible to increase or decrease these
maintenance intervals. Reasons for a change of the intervals can be the items that follow:

•

Environmental and operation conditions

•

Heavy fuel oil and lubricating oil qualities

•

Engine load

•

Cooling water quality

•

Original spare parts used

•

Requirements of classification societies.

For an overview of the maintenance tasks refer to section

17.1 Maintenance overview

X72DF

AA00-0000-00AAA-280B-A

Maintenance Manual

Maintenance schedule

Winterthur Gas & Diesel Ltd.

- 100 -

Issue 002 2020-10

«
...
98
99
100
101
102
...
»

Summary of Contents for X62DF







































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for X62DF

Brand: VAR-SPE Pages: 80

Brand: Daihatsu Pages: 196

Brand: ebm-papst Pages: 9

Reliance CDX7150

Brand: Baldor Pages: 32

Brand: Volvo Penta Pages: 29

Brand: Volvo Penta Pages: 56

Brand: Volvo Penta Pages: 96

Brand: Leadshine Pages: 18

Brand: Kärcher Pages: 116

Brand: AUSTRALIAN MADE Pages: 20

2.0-1120 - V1.1

Brand: MVVS Pages: 2

Brand: MVVS Pages: 6

Brand: Stober Pages: 4

Brand: Paccar Pages: 92

SHOVELHEAD ENGINES

Brand: Ultima Pages: 29

Brand: MINN KOTA Pages: 13

Brand: Baldor Pages: 8

ZA top SM160.40B/S

Brand: ZIEHL-ABEGG Pages: 72

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands