WinGD X62DF Maintenance Manual Download Page 121

Page: 121 / 902

Lift the bearing shell.

5.1

Attach the lifting tool (002,

Figure 6-12

) to the bearing shell (003).

5.2

Turn the bearing shell (003) sufficiently to attach the chain block (001).

5.3

Attach the chain block (001) to the lifting tool (002).

5.4

Operate the chain block (001) to lift the bearing shell (003) a small distance.

5.5

Attach the engine room crane to the lifting tool (002).

5.6

Operate the engine room crane and the chain block (001) to lift and move the
bearing shell (003) out of the engine.

5.7

Remove the chain block (001).

5.8

Operate the engine room crane to move the bearing shell (003) to an applicable
area.

Fig 6-12

Bearing shell - lift

001

002

003

002

CLOSE UP

•

None

X72DF

AA00-1134-00AAA-520A-A

Maintenance Manual

Main bearing shell - remove

Winterthur Gas & Diesel Ltd.

- 121 -

Issue 002 2020-10

Summary of Contents for X62DF







































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for X62DF

Reviews:

Brands by name

Popular brands

WinGD X62DF, Maintenance Manual

Search results

Summary of Contents for X62DF

Reviews:

Brands by name

Popular brands