manualshive.com logo in svg

WinGD X62DF, Maintenance Manual

The WinGD X62DF maintenance manual is available for download for free on our website. This comprehensive manual provides all the information needed to properly care for and maintain your engine. Download it now from manualshive.com to ensure long-lasting performance of your WinGD X62DF engine.

Share
Download
background image

PROCEDURE

1

Put an oil tray under the applicable hydraulic pipe (004, 

Figure 13-4

).

2

Loosen the screws (008) on the flange (003) to drain the applicable hydraulic pipe (004)
through the check bore (006) in the housing of the exhaust valve control unit (VCU)
(002).

3

Remove the six screws (010) from the flange (005).

4

Carefully move the flange (005) away from the top housing (001).

5

Remove the six screws (008) from the flange (003).

6

Carefully move the flange (003) away from the VCU (002).

7

Carefully remove the hydraulic pipe (004).

8

Apply protection to the sealing faces (007, 009) to prevent damage and contamination.

X72DF

AA00-8460-00AAA-520A-A

Maintenance Manual

Hydraulic pipe exhaust valve - remove

Winterthur Gas & Diesel Ltd.

- 733 -

Issue 002 2020-10

Summary of Contents for X62DF







































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for X62DF

S&C Pad-Mounted Series Installation And Operation Manual preview
Pad-Mounted Series
Brand: S&C Pages: 15
3T-Components 3T-MOTORS 3T35-R Installation & Operating Instructions Manual preview
3T-MOTORS 3T35-R
Brand: 3T-Components Pages: 20
Allen-Bradley RDB-B2901 Installation Instructions Manual preview
RDB-B2901
Brand: Allen-Bradley Pages: 32
VM Motori MR704LH Instruction Manual preview
MR704LH
Brand: VM Motori Pages: 62
Stafer V6S-27/13 User Manual preview
V6S-27/13
Brand: Stafer Pages: 6
Volvo Penta TAMD162C Instruction Book preview
TAMD162C
Brand: Volvo Penta Pages: 84
Volvo Penta TAMD61A Workshop Manual preview
TAMD61A
Brand: Volvo Penta Pages: 88
Dato WZ100 Quick Operation Manual preview
WZ100
Brand: Dato Pages: 9
GMC Powertrain 4.3 L Service Manual preview
Powertrain 4.3 L
Brand: GMC Pages: 196
Texas Equipment TG385 User Manual preview
TG385
Brand: Texas Equipment Pages: 38
YS FZ53 Operator'S Manual preview
FZ53
Brand: YS Pages: 2
Kingfisher KD14 Owner'S Handbook Manual preview
KD14
Brand: Kingfisher Pages: 10
DANA 4360-8 Parts List preview
4360-8
Brand: DANA Pages: 2
DANA 4360-78 Parts List preview
4360-78
Brand: DANA Pages: 3
DANA 4360-59 Parts List preview
4360-59
Brand: DANA Pages: 3
DANA 4360-77 Parts List preview
4360-77
Brand: DANA Pages: 3
DANA 4360-80 Parts List preview
4360-80
Brand: DANA Pages: 3
DERRICK EX Maintenance & Operation Manual preview
EX
Brand: DERRICK Pages: 38

Brands by name

Popular brands

Load more brands