WinGD X62DF Maintenance Manual Download Page 558

Page: 558 / 902

Fig 10-11 Pump cylinder removal

007

008

009

010

003
004
005

00425

002

001

006

To remove the pump cylinder, do the steps that follow:

4.1

Turn the pump cover (002,

Figure 10-11

) to point up.

4.2

Use applicable equipment to hold the pump cover (002) to the work bench.

4.3

Remove the screws (001).

4.4

Remove the pump cover (002), valve block (004), valve body (008) and
compression spring (009)

4.5

Remove the circlip (005).

4.6

Remove the intermediate disc (010).

4.7

Remove the screw (006).

4.8

Remove the pump cylinder (007).

NOTE:

The pump cylinder (007) and pump plunger (003) must stay together
as a set.

X72DF

AA00-5556-00AAA-530A-A

Maintenance Manual

Fuel pump - disassemble

Winterthur Gas & Diesel Ltd.

- 558 -

Issue 002 2020-10

Summary of Contents for X62DF







































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for X62DF

Reviews:

Brands by name

Popular brands

WinGD X62DF, Maintenance Manual

Search results

Summary of Contents for X62DF

Reviews:

Brands by name

Popular brands