manualshive.com logo in svg

WinGD X62DF, Maintenance Manual

Share
Download
WinGD X62DF Maintenance Manual Download Page 455

Fig 8-55

 Crosshead - remove

001

002

003

004

005

006

007

008

009

010

003

003

011

00750

011

64

Record the positions of the guide shoes (003, 

Figure 8-56

). The shims of the guide

shoes can have different dimensions (0.3 mm, 0.5 and 1 mm thickness). This will help
you during the installation procedure.

65

Operate the chain blocks (002) to lower the guide shoes (003).

X72DF

AA00-3326-00AAA-520A-A

Maintenance Manual

Crosshead - remove

Winterthur Gas & Diesel Ltd.

- 455 -

Issue 002 2020-10

Summary of Contents for X62DF







































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands