manualshive.com logo in svg

WinGD X62DF, Maintenance Manual

Share
Download
WinGD X62DF Maintenance Manual Download Page 53

2.2.3

 Precautions for work in gas hazardous zones

If you do work in a gas hazardous zone, obey the rules that follow to prevent risks of harm or
damage to personal, to equipment, or to environment:

•

Make sure that you have completed the safety training.

•

Make sure that you have the necessary qualification.

•

Make sure that you have the permission of the safety officer.

•

Ask for the aid of one more person.

•

Make sure that the fuel gas system has no pressure.

•

Make sure that the remaining gas in the fuel gas system is replaced with inert gas (for
example nitrogen).

•

Make sure that the airflow is sufficient for the work area.

•

Make sure that related systems are prevented from an unwanted start. Use the lock-out
and tag-out practice.

•

Use a handheld gas detector.

•

Do not use systems and devices that can cause a spark, for example a cigar lighter,
matches, etc.

•

Do not smoke or start a fire.

•

Put on antistatic clothes.

•

Make sure that your safety shoes are in good condition. Steel toe caps can cause sparks.

•

Use only approved tools that do not cause sparks and test equipment that will not cause
an explosion.

•

Do not use digital cameras, mobile phones or other electronic devices (for example
radios, CD

‑

players).

•

Use only intrinsically safe and approved MHSA two-way radios and transceivers.

•

Use only approved light sources (safety flashlights).

•

If you do welding, obey the instructions of the responsible safety officer and the primary
contractor. Make sure that the responsible safety officer does checks during the welding
work.

•

Read and obey the safety procedures for the ship or for the engine room (for example
security plan, warnings, life-saving devices, escape routing, meeting point, gas
hazardous zones, special instructions on the safety notice board).

•

Keep your work area clean. Remove flammable material immediately.

X72DF

AA00-0000-00AAA-012H-A

Maintenance Manual

Safety precautions and safety rules for natural gas

Winterthur Gas & Diesel Ltd.

- 53 -

Issue 002 2020-10

Summary of Contents for X62DF







































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands