manualshive.com logo in svg

WinGD X62DF, Maintenance Manual

Share
Download
WinGD X62DF Maintenance Manual Download Page 213

14.7

Turn the rod (001) back to release the tension in the spring (006). Make sure
that the valve cotter (003) is installed correctly in the spring carrier (012).

14.8

Remove the dismantling and assembling tool and the bracket from the bush
(007).

15

Do the test procedure given in 

Step 3

 to 

Step 11

 again.

16

If the leakage is unsatisfactory, replace the valve spindle and valve guide.

CLOSE UP

•

None

X72DF

AA00-2140-00AAA-362A-A

Maintenance Manual

Gas admission valve - do a check for gas leakage

Winterthur Gas & Diesel Ltd.

- 213 -

Issue 002 2020-10

Summary of Contents for X62DF







































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands